background image

This product can be set up using 

any current web browser:

Internet Explorer 6 or Netscape 

Navigator 7

DI-524UP

AirPlus G   

Wireless Router 

and USB Print Server

5V 2A DC Power Adapter

©2004, 2005 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their 

respective holders. Software and specifications subject to change without notice. 

Before You Begin

If you purchased this router to share your high-speed Internet connection with 

other computers, you must have either an Ethernet-based Cable or DSL modem 

with an established Internet account from an Internet Service Provider (ISP).

2. 

It’s best to use the same computer that is connected to your modem for configuring 

the DI-524UP 

Air

Plus G Wireless Router. The DI-524UP acts as a DHCP server and 

will assign all the necessary IP address information on your network. 

See Appendix 

at the end of this Quick Installation Guide or the Manual on the CD-ROM for 

setting each network adapter to automatically obtain an IP address.

Check Your Package Contents

DI-524UP 

Air

Plus G 802.g/2.4GHz Wireless 

Router

CD-ROM (containing Manual and Warranty)

Ethernet (CAT5 UTP/Straight Through) Cable

     

Using a power 

supply with a different 

voltage rating will 

damage and void the 

warranty of this product.

If any of the above items are missing, please contact your reseller.

Summary of Contents for DI-524UP












Reviews: