background image

Software:

D-Link warrants that the software programs licensed from it will perform in substantial conformance to the
applicable published program specifications for a period of ninety (90) days from the date of purchase from
D-Link or its Authorized Reseller.  D-Link warrants the magnetic media containing software against failure
during the warranty period.  No updates are provided. D-Link's sole obligation hereunder shall be to replace
any defective software products with products which substantially conform to D-Link's applicable published
specifications.  Customer assumes responsibility for the selection of the appropriate applications program and
associated reference materials. D-Link makes no warranty that its software products will work in combination
with any hardware or applications software products provided by third party, that the operation of the
software products will be uninterrupted or error free, or that all defects in the software product will be
corrected. For any third party products listed in the D-Link software product documentation or specifications
as being compatible, D-Link will make reasonable efforts to provide compatibility, except where the non-
compatibility is caused by "bug" or defect in the third party's product.

Warranty service for software products may be obtained by contacting a D-Link office within the warranty
period.  Where no Product Registration Card has been sent by Customer, proof of purchase, such as a copy of
the dated purchased invoice, must be provided.

D-Link Offices to Contact for Warranty Service:

To obtain an RMA number for warranty service, contact the D-Link office nearest you.  A list of contact
addresses for D-Link’s international offices is found in the back of this User’s Guide.  Your Warranty
Registration Card should also be sent to your regional D-Link office.

Summary of Contents for DP-100

































Reviews: