background image

36

DWL-8220AP User’s Manual 

D-Link Systems, Inc.

FCC Statement:

 This equipment has been tested and found to comply with the limits for 

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. This 
equipment  generates,  uses,  and  can  radiate  radio  frequency  energy  and,  if  not  installed 
and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 
communication. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:
 

• Reorient or relocate the receiving antenna.

 

• Increase the separation between the equipment and receiver.

 

• Connect the equipment into an outlet on a circuit different from that to which the 

 

   receiver is connected.

 

• Consult the dealer or an experienced radio/TV technician for help.

For detailed warranty outside the United States, please contact corresponding local D-Link 
office. 

FCC Caution:

The manufacturer is not responsible for any radio or TV interference caused by unauthorized 
modifications to this equipment; such modifications could void the user’s authority to operate 
the equipment.
 

(1) The devices are restricted to indoor operations within the 5.15 to 5.25GHz range.  

 

(2) For this device to operate in the 5.15 to 5.25GHz range, the devices must use 

 

      integral antennas.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions:
 

(1) This device may not cause harmful interference, and

 

(2) this device must accept any interference received, including interference that may 

 

     cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure 
limits set forth for an uncontrolled environment. The antenna(s) used for this equipment must 
be installed to provide a separation distance of at least eight inches (20 cm) from all persons. 
This equipment must not be operated in conjunction with any other antenna.

Warranty (continued)

Warranty

Summary of Contents for DWL-8220AP - AirPremier Wireless Switch Dualband Access...






































Reviews: