manualshive.com logo in svg

D-Link DWS-3024L, User Manual

The D-Link DWS-3024L is an advanced network switch designed for seamless connectivity. With its reliable performance and extensive features, configuring and optimizing your network has never been easier. Enhance your user experience by downloading the free user manual from our website to explore the full potential of this exceptional product.

Share
Download
background image

Configuring the WLAN and Tunnel Interfaces    215

   L3 Roaming Example

Some phone system require placement of a call server on the same subnet as the phones. The 
D-Link tunneling feature supports this configuration.

There are a few things to consider when planning a network with L3 roaming capabilities:

•

Packets that use the L3 tunnel have an extra 20 bytes in the header for encapsulation.

•

To support these larger frames, you can increase the MTU size on all intermediate ports 
and Unified Switch ports.

•

If you use tunneling only for IP telephony, or if you set the MTU size on all wireless 
clients that use tunneling to 1480, you do not need to increase the MTU size in the 
network.

•

For traffic in the L3 tunnel, the switch forwards IPv4 unicast frames in hardware; other 
types of traffic, such as multicast and non-IP traffic, are forwarded in software.
-

Multicast and non-IP traffic on the L3 tunneling network could cause network 
congestion.

-

Wireless tunneling does not work if IPv6 or multicast traffic is enabled on the L3 
tunnel interface.

•

All devices that use the L3 tunnel network are stored in the ARP cache because the 
wireless subnet is local to the switch, which means the ARP cache can fill up faster than 
expected.

•

When tunneled clients are used in conjunction with peer switches, one of the peer switches 
must be configured as a default gateway for the tunneled clients. Normally the default 
gateway routes all traffic from the client’s subnet to other subnets, however in a peer 
switch network the Unified Switch that manages the AP to which the client is associated 
routes the frames into the remote subnets. This means that each peer switch must have 
routing table entries that enable it to route frames to every subnet in the network.

Using a Loopback Interface for the Wireless Functions

By creating a loopback interface, you can control which routing interface the wireless function 
uses for its IP address when multiple routing interfaces exist. With the loopback interface, the 
IP address of the wireless function is always the same.

NOTE:

In this context, the loopback interface does not refer to the loopback interface 
with the 127.0.0.1 IP address. When you configure a loopback interface for 
the wireless interface on the switch, it is essentially a permanent logical inter-
face and cannot have an IP address of 127.0.0.1. You must create a dedicated 
subnet for the loopback interface, and other devices on the network must be 
able to contact the IP address of the loopback interface.

You must create static routes so other devices can find the loopback interface.

The advantage of defining a loopback interface is that the interface never goes down. The 
disadvantage is that network configuration is more complex because the loopback interface is 
located on its own subnet and the rest of the network must know how to get to the subnet.

The network must have routes between the Unified Switch and the APs to manage. The APs 
must be able to ping the IP address of the loopback interface used as the WLAN interface on 
the Unified Switch. 

The following procedures show an example of how to enable routing and configure an IP 
address on a loopback or routing interface. 

Summary of Contents for DWS-3024L













































































































































































































































































Reviews:

No comments

Related manuals for DWS-3024L

D-Link DAP-1365 Setup Procedure preview
DAP-1365
Brand: D-Link Pages: 3
Cerio WP-300N Quick Start Manual preview
WP-300N
Brand: Cerio Pages: 13
Planet WAP-7000 User Manual preview
WAP-7000
Brand: Planet Pages: 29
BridgeWave FLEX4G-LITE User Interface Manual preview
FLEX4G-LITE
Brand: BridgeWave Pages: 84
Mobility Sound BTD-3M2 User Manual preview
BTD-3M2
Brand: Mobility Sound Pages: 2
NETGEAR RAX15 Quick Start preview
RAX15
Brand: NETGEAR Pages: 2
Alloy WLF2454AP-S User Manual preview
WLF2454AP-S
Brand: Alloy Pages: 30
ADTRAN BLUESOCKET 1930 Quick Start Manual preview
BLUESOCKET 1930
Brand: ADTRAN Pages: 4
TP-Link TL-WR710N Quick Installation Manual preview
TL-WR710N
Brand: TP-Link Pages: 2
Cambium Networks PTP 550E Series User Manual preview
PTP 550E Series
Brand: Cambium Networks Pages: 250
Kraun KR.KZ User Manual preview
KR.KZ
Brand: Kraun Pages: 35
Airlinkplus RT211W Quick Installation Manual preview
RT211W
Brand: Airlinkplus Pages: 4
Airlink101 AR335W User Manual preview
AR335W
Brand: Airlink101 Pages: 44
Airlink101 AR670W User Manual preview
AR670W
Brand: Airlink101 Pages: 48
Airlink101 LX60 Hardware User'S Manual preview
LX60
Brand: Airlink101 Pages: 66
Aruba 303 Series Startup Manual preview
303 Series
Brand: Aruba Pages: 2
Comcast 781W User Manual preview
781W
Brand: Comcast Pages: 57
HPE Aruba AP-574 Product End-Of-Life Disassembly Instructions preview
Aruba AP-574
Brand: HPE Pages: 4

Brands by name

Popular brands

Load more brands