DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
712
Parameters
<int 1-16>
- Enter the wireless AP Profile ID used here. This value must be between 1 and 16.
apply
- Specifies to resend the AP profile configuration to all managed APs associated with the
profile. This allows you to apply configuration changes to the APs that are already managed.
clear
- Specifies to restores an AP profile configuration to its default values, except for the profile
name. The profile name is not an AP configuration and is only used for descriptive purposes.
hwtype
- Specifies to configure the AP hardware type. The hardware type is determined, in part,
by the number of radios the AP supports (single or dual) and the IEEE 802.11 modes that the
radio supports.
Any
- Specifies a general AP hardware type. Dual Radio 802.11a/b/g/n.
hw_dwl8600
- Specifies that the AP hardware type is a DWL-8600AP, Dual Radio
802.11a/b/g/n.
hw_dwl3600
- Specifies that the AP hardware type is a DWL-3600AP, Single Radio
802.11b/g/n.
hw_dwl6600
- Specifies that the AP hardware type is a DWL-6600AP, Dual Radio
802.11a/b/g/n.
name
- Specifies the descriptive name for the AP Profile.
<name 32>
- Enter the descriptive name for the AP Profile here. This name can be up to 32
characters long.
vlan
- Specifies the VLAN ID used to send tracer packets using the wired network detection
algorithm. If VLAN ID is '0', then tracer packets will be sent untagged.
<int 0-4094>
- Enter the VLAN ID used to send tracer packets using the wired network
detection algorithm here. This value must be between 0 and 4094. The default value is 1.
default
- Specifies that the default option will be used.
disconnected_ap
- Specifies the behavior of an AP when it disconnects.
forwarding_mode
- Specifies to configure the AP's forwarding mode state. This also specifies
whether the managed AP should allow clients that are already associated to continue
forwarding traffic when the AP loses connection with the wireless Switch. If this field is
disabled, the AP will not allow clients to forward data if the AP loses its connection with the
Switch that is managing it.
enable
- Specifies that the AP's forwarding mode will be enabled.
disable
- Specifies that the AP's forwarding mode will be disabled. This is the default
option.
management_mode
- Specifies to configure the AP's management mode state. This also
specifies whether the managed AP should enable the stand-alone management
functionality when it loses connection with the wireless Switch. If this field is disabled, the
AP will not allow TELNET, Web, or SNMP access to the stand-alone management
interface.
enable
- Specifies that the AP's management mode will be enabled. This is the default
option.
disable
- Specifies that the AP's management mode will be disabled.
radio
- Specifies the RF configuration for a radio interface within an access point profile.
<int 1-2>
- Enter the RF configuration value for a radio interface within an access point profile
here. This value must be between 1 and 2.
uapsd
- Specifies the state of the automatic power save delivery mode for the radio.
enable
- Specifies that the automatic power save delivery mode for the radio will be
enabled. This is the default option.
disable
- Specifies that the automatic power save delivery mode for the radio will be
disabled.
beacon_interval
- Specifies the beacon interval for the radio. The beacon interval indicates
the interval at which the AP radio transmits beacon frames.
<int 20-2000>
- Enter the beacon interval value for the radio here. This value must be
between 20 and 2000 milliseconds. The default value is 100 milliseconds.
default
- Specifies that the default value will be used.
channel auto
- Specifies the automatic channel adjustment for the radio. This indicates that
the initial AP channel assignment can be automatically adjusted by the Switch.
enable
- Specifies that the automatic channel adjustment feature will be enabled.
disable
- Specifies that the automatic channel adjustment feature will be disabled. This is
the default option.
