DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
713
auto_eligible
- Specifies to enable either one or all of the supported channels on the radio to
be eligible for auto-channel selection. If you Specifies one channel, the command will
succeed only if this channel is supported by the current mode of the radio. If 'all' is chosen,
then all channels supported by the current radio mode will be enabled for automatic
selection.
add
- Specifies to add a channel in the automatic eligible group.
<int>
- Enter the automatic eligible channel number that will be added here.
all
- Specifies that all the available channels will be added to the automatic eligible
group. This is the default option.
delete
- Specifies to delete a channel from the automatic eligible group.
<int>
- Enter the automatic eligible channel number that will be deleted here.
all
- Specifies that all the channels will be removed from the automatic eligible group.
dot11n
- Specifies that parameters regarding the 802.11n channel bandwidth will be
configured.
channel_bandwidth
- Specifies the bandwidth used by the channel when operating in
802.11n mode.
20
- Specifies the radio will operate in the 20MHz bandwidth.
40
- Specifies the radio will operate in the 40MHz bandwidth. This is the default option.
primary_channel
- Specifies the bandwidth used by the channel when operating in
802.11n mode.
lower
- Specifies that the relative location of the primary channel will be on the lower
side in the 40 MHz channel. This is the default option.
upper
- Specifies that the relative location of the primary channel will be on the upper
side in the 40 MHz channel.
default
- Specifies that the default option will be used.
short_guard_interval
- Specifies the short guard interval's state, when operating in
802.11n mode.
enable
- Specifies that the short guard interval will be enabled. The guard interval value
is set as 400ns. This is the default option.
disable
- Specifies that the short guard interval will be disabled. The guard interval
value is set as 800ns.
default
- Specifies that the default option will be used.
stbc_mode
- Specifies the Space Time Block Code (STBC) mode when operating in
802.11n mode. The STBC enables the AP to send the same data stream on multiple
antennas at the same time.
enable
- Specifies to send the same data stream on multiple antennas at the same
time. This is the default option.
disable
- Specifies to divide the same data stream between two antennas.
default
- Specifies that the default option will be used.
dtim_period
- Specifies the DTIM period for the radio. The DTIM period is the number of
beacons between DTIMs. A DTIM is Delivery Traffic Indication Map which indicates there
is buffered broadcast or multicast traffic on the AP.
<int 1-255>
- Enter the DTIM period value used here. This value must be between 1 and
255. The default value is 10 beacons.
default
- Specifies that the default value will be used.
status
- Specifies the administrative mode of the radio interface to the ‘on' state.
enable
- Specifies that the administrative mode of the radio interface to the 'on' state will
be enabled. This is the default option.
disable
- Specifies that the administrative mode of the radio interface to the 'on' state will
be disabled.
fragmentation_threshold
- Specifies the fragmentation threshold for the radio. The
fragmentation threshold indicates a limit on the size of packets that can be fragmented. A
threshold of 2346 indicates that there should be no fragmentation.
<int 256-2346>
- Enter the fragmentation threshold value used here. This value must be
between 256 and 2346. The default value is 2346.
default
- Specifies that the default value will be used.
incorrect_frame_no_ack
- Specifies whether or not to send any acknowledgements for
incorrectly received frames.
enable
- Specifies not to send any acknowledgements for incorrectly received frames. This
is the default option.
