DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
717
stations.
add
- Specifies to add a supported data rate to the corresponding list.
<float>
- Enter a valid data rate, in Mbps, here based on the radio mode.
delete
- Specifies to delete a supported data rate from the corresponding list.
<float>
- Enter a valid data rate, in Mbps, here based on the radio mode.
rate_limit
- Specifies that enabling the multicast and broadcast rate limitation can improve
overall network performance by limiting the number of packets transmitted across the
network.
state
- Specifies the broadcast and multicast traffic rate limitation's state on the radio.
enable
- Specifies that the broadcast and multicast traffic rate limitation's state on the
radio will be enabled.
disable
- Specifies that the broadcast and multicast traffic rate limitation's state on the
radio will be disabled. This is the default value.
burst
- Specifies to configure the burst traffic rate. Traffic can occur in bursts up to this
value before all traffic is considered to exceed the limit.
<int 1-75>
- Enter the burst traffic rate value used here. This value must be between 1
and 75 packets per second. The default value is 75 packets per second.
default
- Specifies that the default value will be used.
normal
- Specifies to configure the rate limit for normal traffic. All traffic below this limit is
transmitted.
<int 1-50>
- Enter the rate limit for normal traffic used here. This value must be between
1 and 50 packets per second. The default value is 50 packets per second.
default
- Specifies that the default value will be used.
rf_scan
- Specifies that the FR scan feature will be configured.
duration
- Specifies the RF scan duration for the radio. The duration indicates how long
the radio will scan on one channel.
<int 10-2000>
- Enter the RF scan duration value used here. This value must be
between 10 and 2000ms. The default value is 10ms.
default
- Specifies that the default value will be used.
other_channel
- Specifies that the access point can perform RF scans to collect
information about other wireless devices within range and then report this information to
the UWS.
mode
- Specifies to enable or disable the radio to perform RF scanning on channels
other than its operating channel.
enable
- Specifies that the radio will perform RF scanning on channels other than its
operating channel. This is the default option.
disable
- Specifies that the radio will not perform RF scanning on channels other than
its operating channel.
interval
- Specifies how often the radio will leave its operational channel.
<int 30-120>
- Enter the interval value used here. This value must be between 30 and
120 seconds. The default value is 60 seconds.
default
- Specifies that the default value will be used.
sentry
- Specifies that when the RF Scan Sentry option is enabled, the radio primarily
performs dedicated RF scanning. The radio passively listens for beacons and traffic
exchanges between clients and other access points but does not accept connections
from wireless clients. In sentry mode, all VAPs are disabled. Networks that deploy
sentry APs or radios can detect devices on the network quicker and perform a more
thorough security analysis. In this mode, the radio Switches from one channel to the
next. The length of time spent on each channel is controlled by the scan duration. The
default scan duration is 10 milliseconds.
mode
- Specifies whether to enable or disable dedicated RF scanning and normal
operation of the radio. The radio will not allow any client associations when sentry mode
is enabled.
enable
- Specifies that the sentry mode will be enabled.
disable
- Specifies that the sentry mode will be disabled. This is the default option.
channels
- Specifies to scan channels within the specified mode or frequency.
an
- Specifies to perform an RF scan on all 802.11a/n channels on the 5GHz frequency.
all
- Specifies to perform an RF scan on all the channels. This is the default option.
bgn
- Specifies to perform an RF scan on all 802.11b/g/n channels on the 2.4GHz
frequency.
