background image

About This Guide  

D-Link DXS-1210 Series User Manual

 

1

 

 

About This Guide 

This guide provides  installation and instructions  for the D-Link  10  Gigabit  Ethernet  L2  Switch  (DXS-1210-
12TC/12SC/10TS), 

 

Note:

  The model you have purchased may 

appear slightly different from the illustrations 
shown in the document.  Refer  to the  Product 
Instruction  and  Technical Specification  sections 
for  detailed information about your switch, its 
components, network connections, and technical 
specifications. 

 

This guide is divided into four parts: 

1. 

Hardware Installation: Step-by-step hardware installation procedures.  

2. 

Getting Started: A startup guide for basic switch installation and settings. 

3. 

D-Link Network Assistant: An introduction to the central configuration utility. 

4. 

Configuration: Information about the function descriptions and configuration settings. 

 

Terms/Usage 

In this guide, the term “Switch” (first letter capitalized) refers to the DSX-1210 Series switch and “switch” (first 
letter lower case) refers to other Ethernet switches. Some technologies use “switch”, “bridge” and “switching 
hubs” interchangeably, and all are commonly accepted terms for Ethernet switches. 

 

 

NOTE

  indicates important  information that 

helps you make better use of the device. 

 

 

CAUTION

  indicates potential property for 

property damage or personal injury.  

 

 

Copyright and Trademarks 

Information in this document is subjected to change without notice. 

© 2016 D-Link Corporation. All rights reserved. 

Reproduction in any manner whatever without the written permission of D-Link Corporation is strictly 
forbidden. 

Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft 
and Windows are registered trademarks of Microsoft Corporation. 

Other trademarks and trade names may be used in this document to refer to either the entities claiming the 
marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and 
trade names other than its own. 

Summary of Contents for DXS-1210 Series





















Reviews: