manualshive.com logo in svg

D-Link NetDefend DFL-260E, User Manual

The D-Link NetDefend DFL-260E is a powerful network security appliance designed to safeguard your data and network infrastructure. Ensure a seamless setup with the Quick Installation Manual, available for free download from 88.208.23.73:8080. Discover comprehensive instructions and get the most out of your device hassle-free.

Share
Download
background image

4.2. Static Routing

The most basic form of routing is known as Static Routing. The word "static" refers to the fact that
entries in the routing table are manually added and are therefore permanent (or static) by nature.

Due to this manual approach, static routing is most appropriate to use in smaller network
deployments where addresses are fairly fixed and where the amount of connected networks are
limited to a few. However, for larger networks, or whenever the network topology is complex, the
work of manually maintaining static routing tables can be time-consuming and also problematic.
Dynamic routing should therefore be used in such cases.

For more information about the dynamic routing capabilities of NetDefendOS, please see
Section 4.5, “OSPF”. Note, however, that even if dynamic routing is chosen for a network,
understanding the principles of static routing and how it is implemented in NetDefendOS is still
required.

4.2.1. The Principles of Routing

IP routing is the mechanism used in TCP/IP based networks for delivering IP packets from their
source to their ultimate destination through a number of intermediary network devices. These
devices are most often referred to as routers since they are performing the task of routing packets to
their destination.

In each router, one or more routing tables contain a list of routes and these are consulted to find out
where to send a packet so it can reach its destination. The components of a single route are
discussed next.

The Components of a Route

When a route is defined it consists of the following parameters:

•

Interface

The interface to forward the packet on in order to reach the destination network. In other words,
the interface to which the destination IP range is connected, either directly or through a router.

The interface might be a physical interface of the firewall or it might be VPN tunnel (tunnels are
treated like physical interfaces by NetDefendOS).

•

Network

This is the destination network IP address range which this route will reach. The route chosen
from a routing table is the one that has a destination IP range which includes the IP address
being sought. If there is more than one such matching route, the route chosen is the one which
has the smallest IP address range.

The destination network all-nets is usually always used in the route for public Internet access via
an ISP.

•

Gateway

The IP address of the gateway which is the next router in the path to the destination network.
This is optional. If the destination network is connected directly to the interface, this is not
needed.

When a router lies between the NetDefend Firewall and the destination network, a gateway IP
must be specified. For example, if the route is for public Internet access via an ISP then the
public IP address of the ISP's gateway router would be specified.

•

Local IP address

4.2. Static Routing

Chapter 4. Routing

148

Summary of Contents for NetDefend DFL-260E









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetDefend DFL-260E

Siemens SIMATIC NET SCALANCE S615 Configuration Manual preview
SIMATIC NET SCALANCE S615
Brand: Siemens Pages: 320
Yamaha FWX120 Operation Manual preview
FWX120
Brand: Yamaha Pages: 194
Recon Sentinel Quick Start Manual preview
Sentinel
Brand: Recon Pages: 2
Tosibox Lock 200 User Manual preview
Lock 200
Brand: Tosibox Pages: 44
PaloAlto Networks PA-3400 Series Hardware Reference Manual preview
PA-3400 Series
Brand: PaloAlto Networks Pages: 50
Barracuda Networks NG FIREWALL Release Notes preview
NG FIREWALL
Brand: Barracuda Networks Pages: 24
Thales KeySecure k570 Installation Manual preview
KeySecure k570
Brand: Thales Pages: 37
NETGEAR FVS336G - ProSafe Dual WAN Gigabit Firewall Reference Manual preview
FVS336G - ProSafe Dual WAN Gigabit Firewall
Brand: NETGEAR Pages: 10
NETGEAR FVS318 - ProSafe VPN Firewall Router Reference Manual preview
FVS318 - ProSafe VPN Firewall Router
Brand: NETGEAR Pages: 20
NETGEAR FVS124G - ProSafe VPN Firewall 25 Configuration Manual preview
FVS124G - ProSafe VPN Firewall 25
Brand: NETGEAR Pages: 35
NETGEAR ProSafe FR328S Reference Manual preview
ProSafe FR328S
Brand: NETGEAR Pages: 131
NETGEAR FVS114NA Reference Manual preview
FVS114NA
Brand: NETGEAR Pages: 212
NETGEAR FVL328 - Cable/DSL ProSafe VPN Firewall Router Reference Manual preview
FVL328 - Cable/DSL ProSafe VPN Firewall Router
Brand: NETGEAR Pages: 240
Watchguard Firebox T85 Quick Start Manual preview
Firebox T85
Brand: Watchguard Pages: 2

Brands by name

Popular brands

Load more brands