D-Link NetDefend DFL-260E User Manual Download | Manualshive

Page: 170 / 552

background image

4.4. Route Load Balancing

Overview

NetDefendOS provides the option to perform Route Load Balancing (RLB). This is the ability to
distribute traffic over multiple alternate routes using one of a number of distribution algorithms.

The purpose of this feature is to provide the following:

•

Balancing of traffic between interfaces in a policy driven fashion.

•

To balance simultaneous utilization of multiple Internet links so networks are not dependent on
a single ISP.

•

To allow balancing of traffic across multiple VPN tunnels which might be setup over different
physical interfaces.

Enabling RLB

RLB is enabled on a routing table basis and this is done by creating an RLB Instance object. This
object specifies two parameters: a routing table and an RLB algorithm. A table may have only one
Instance object associated with it.

One of the algorithms from the following list can be specified in an RLB Instance object:

•

Round Robin

Matching routes are used equally often by successively going to the next matching route.

•

Destination

This is an algorithm that is similar to Round Robin but provides destination IP "stickiness" so
that the same destination IP address gets the same route.

•

Spillover

This uses the next route when specified interface traffic limits are exceeded continuously for a
given time.

Disabling RLB

Deleting a routing table's Instance object has the effect of switching off RLB for that table.

RLB Operation

When RLB is enabled for a routing table through an RLB Instance object, the sequence of
processing steps is as follows:

1.

Route lookup is done in the routing table and a list of all matching routes is assembled. The
routes in the list must cover the exact same IP address range (further explanation of this
requirement can be found below).

2.

If the route lookup finds only one matching route then that route is used and balancing does not
take place.

3.

If more than one matching route is found then RLB is used to choose which one to use. This is

4.4. Route Load Balancing

Chapter 4. Routing

170

«
...
168
169
170
171
172
...
»

Summary of Contents for NetDefend DFL-260E









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetDefend DFL-260E

Brand: IBM Pages: 2

NetDefend DFL-2560G

Brand: D-Link Pages: 44

Brand: NETGEAR Pages: 2

Brand: Siemens Pages: 62

ZyXEL ZyWALL USG-1000

Brand: ZyXEL Communications Pages: 986

SUPERSTACK 3CR16110-95

Brand: 3Com Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands