Sometimes there is a need to include networks into the OSPF routing process, without running
OSPF on the interface connected to that network. This is done by enabling the option:
No OSPF routers connected to this interface ("Passive").
This is an alternative to using a Dynamic Routing Policy to import static routes into the OSPF
routing process.
If the Ignore received OSPF MTU restrictions is enabled, OSPF MTU mismatches will be
allowed.
4.5.3.4. OSPF Neighbors
In some scenarios the neighboring OSPF router to a firewall needs to be explicitly defined. For
example, when the connection is not between physical interfaces.
The most common situation for using this is when a VPN tunnel is used to connect two neighbors
and we need to tell NetDefendOS that the OSPF connection needs to be made through the tunnel.
This type of VPN usage with IPsec tunnels is described further in Section 4.5.5, “Setting Up
OSPF”.
NetDefendOS OSPF Neighbor objects are created within an OSPF Area and each object has the
following property parameters:
Interface
Specifies which OSPF interface the neighbor is located on.
IP Address
The IP Address of the neighbor. This is the IP Address of the neighbors OSPF
interface connecting to this router. For VPN tunnels this will be the IP address of
the tunnel's remote end.
Metric
Specifies the metric to this neighbor.
4.5.3.5. OSPF Aggregates
OSPF Aggregation is used to combine groups of routes with common addresses into a single entry
in the routing table. If advertised this will decreases the size of the routing table in the firewall, if
not advertised this will hide the networks.
NetDefendOS OSPF Aggregate objects are created within an OSPF Area and each object has the
following parameters:
Network
The network consisting of the smaller routers.
Advertise
If the aggregation should be advertised or not.
In most, simple OSPF scenarios, OSPF Aggregate objects will not be needed.
4.5.3.6. OSPF VLinks
All areas in an OSPF AS must be physically connected to the backbone area (the area with ID 0). In
some cases this is not possible and in that case a Virtual Link (VLink) can be used to connect to the
backbone through a non-backbone area.
NetDefendOS OSPF VLink objects are created within an OSPF Area and each object has the
following parameters:
General Parameters
Name
Symbolic name of the virtual link.
Neighbor Router ID
The Router ID of the router on the other side of the virtual link.
4.5.3. OSPF Components
Chapter 4. Routing
189
Summary of Contents for NetDefend DFL-260E
