manualshive.com logo in svg

D-Link NetDefend DFL-260E, User Manual

The D-Link NetDefend DFL-260E is a powerful network security appliance designed to safeguard your data and network infrastructure. Ensure a seamless setup with the Quick Installation Manual, available for free download from 88.208.23.73:8080. Discover comprehensive instructions and get the most out of your device hassle-free.

Share
Download
background image

the OSI model. If the firewall is placed into a network for the first time, or if network topology
changes, the routing configuration must therefore be checked and adjusted to ensure that the routing
table is consistent with the new layout. Reconfiguration of IP settings may be required for
pre-existing routers and protected servers. This works well when comprehensive control over
routing is desired.

With switch routes, the NetDefend Firewall operates in Transparent Mode and resembles a OSI
Layer 2 Switch in that it screens IP packets and forwards them transparently to the correct interface
without modifying any of the source or destination information at the IP or Ethernet levels. This is
achieved by NetDefendOS keeping track of the MAC addresses of the connected hosts and
NetDefendOS allows physical Ethernet networks on either side of the NetDefend Firewall to act as
though they were a single logical IP network. (See Appendix D, The OSI Framework for an
overview of the OSI layer model.)

Two benefits of Transparent Mode over conventional routing are:

•

A user can move from one interface to another in a "plug-n-play" fashion, without changing
their IP address (assuming their IP address is fixed). The user can still obtain the same services
as before (for example HTTP, FTP) without any need to change routes.

•

The same network address range can exist on several interfaces.

Note: Transparent and Routing Mode can be combined

Transparent Mode and Routing Mode can operate together on a single NetDefend
Firewall. Switch Routes can be defined alongside standard non-switch routes although
the two types cannot be combined for the same interface. An interface operates in one
mode or the other.

It is also possible to create a hybrid case by applying address translation on otherwise
transparent traffic.

How Transparent Mode Works

In Transparent Mode, NetDefendOS allows ARP transactions to pass through the NetDefend
Firewall, and determines from this ARP traffic the relationship between IP addresses, physical
addresses and interfaces. NetDefendOS remembers this address information in order to relay IP
packets to the correct receiver. During the ARP transactions, neither of the endpoints will be aware
of the NetDefend Firewall.

When beginning communication, a host will locate the target host's physical address by
broadcasting an ARP request. This request is intercepted by NetDefendOS and it sets up an internal
ARP Transaction State entry and broadcasts the ARP request to all the other switch-route interfaces
except the interface the ARP request was received on. If NetDefendOS receives an ARP reply from
the destination within a configurable timeout period, it will relay the reply back to the sender of the
request, using the information previously stored in the ARP Transaction State entry.

During the ARP transaction, NetDefendOS learns the source address information for both ends from
the request and reply. NetDefendOS maintains two tables to store this information: the Content
Addressable Memory (CAM) and Layer 3 Cache. The CAM table tracks the MAC addresses
available on a given interface and the Layer 3 cache maps an IP address to MAC address and
interface. As the Layer 3 Cache is only used for IP traffic, Layer 3 Cache entries are stored as single
host entries in the routing table.

For each IP packet that passes through the NetDefend Firewall, a route lookup for the destination is
done. If the route of the packet matches a Switch Route or a Layer 3 Cache entry in the routing
table, NetDefendOS knows that it should handle this packet in a transparent manner. If a destination
interface and MAC address is available in the route, NetDefendOS has the necessary information to
forward the packet to the destination. If the route was a Switch Route, no specific information about
the destination is available and the firewall will have to discover where the destination is located in

4.7.1. Overview

Chapter 4. Routing

213

Summary of Contents for NetDefend DFL-260E









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetDefend DFL-260E

Genetec SV-32 Quick Start Manual preview
SV-32
Brand: Genetec Pages: 16
HP Photosmart 7500 Quickspecs preview
Photosmart 7500
Brand: HP Pages: 84
ZyXEL Communications Unified Security Gateway ZyWALL 300 User Manual preview
Unified Security Gateway ZyWALL 300
Brand: ZyXEL Communications Pages: 1156
PaloAlto Networks PA-1400 Series Hardware Reference Manual preview
PA-1400 Series
Brand: PaloAlto Networks Pages: 46
Fing Fingbox User Manual preview
Fingbox
Brand: Fing Pages: 58
Watchguard Firebox T85 Quick Start Manual preview
Firebox T85
Brand: Watchguard Pages: 2
Edge-Core SAF51003I Quick Start Manual preview
SAF51003I
Brand: Edge-Core Pages: 4

Brands by name

Popular brands

Load more brands