D-Link NetDefend DFL-260E User Manual Download | Manualshive

Page: 387 / 552

background image

9.2. VPN Quick Start

Overview

Later sections in this chapter will explore VPN components in detail. To help put those later
sections in context, this section is a quick start summary of the steps needed for VPN setup.

It outlines the individual steps in setting up VPNs for the most common scenarios. These are:

•

IPsec LAN to LAN with Pre-shared Keys

•

IPsec LAN to LAN with Certificates

•

IPsec Roaming Clients with Pre-shared Keys

•

IPsec Roaming Clients with Certificates

•

L2TP Roaming Clients with Pre-Shared Keys

•

L2TP Roaming Clients with Certificates

•

PPTP Roaming Clients

Common Tunnel Setup Requirements

Before looking at each of these scenarios separately, it is useful to summarize the common
NetDefendOS requirements when setting up any VPN tunnel, regardless of the type.

•

Define the Tunnel

Firstly we must define the tunnel itself. NetDefendOS has various tunnel object types which are
used to do this, such as an IPsec Tunnel object.

•

A Route Must Exist

Before any traffic can flow into the tunnel, a route must be defined in a NetDefendOS routing
table. This route tells NetDefendOS which network can be found at the other end of the tunnel
so it knows which traffic to send into the tunnel.

In most cases, this route is created automatically when the tunnel is defined and this can be
checked by examining the routing tables.

If a route is defined manually, the tunnel is treated exactly like a physical interface in the route
properties, as it is in other aspects of NetDefendOS. In other words, the route is saying to
NetDefendOS that a certain network is found at the other end of the tunnel.

•

Define an IP Rule to Allow VPN Traffic

An IP rule must be defined that explicitly allows traffic to flow between a network and the
tunnel. As with route definitions, the tunnel is treated exactly like a physical interface when
defining the IP rule.

IP rules are not created automatically after defining the tunnel object and if they do not exist
then no traffic can flow through the tunnel and will instead, be dropped.

The following sections will look at the detailed setup for each of the VPN scenarios listed earlier.

9.2. VPN Quick Start

Chapter 9. VPN

387

«
...
385
386
387
388
389
...
»

Summary of Contents for NetDefend DFL-260E









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetDefend DFL-260E

Brand: Lanner Pages: 63

Brand: Plextor Pages: 70

Brand: SonicWALL Pages: 21

GoSilent GSC-100

Brand: Silent Circle Pages: 10

TPL NET Network Module

Brand: Teknim Pages: 3

appliance watchdog

Brand: 8e6 Technologies Pages: 50

Brand: IS5 COMMUNICATIONS Pages: 47

Brand: Belden Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands