Note: The symbol $0 is reserved
Notice that the name of the first variable is $1. The variable $0 is reserved and is
always replaced before execution by the name of the script file itself.
For example, a script called my_script.sgs is to be executed with IP address 126.12.11.01 replacing
all occurrences of $1 in the script file and the string If1 address replacing all occurrences of $2.
The file my_script.sgs contains the single CLI command line:
add IP4Address If1_ip Address=$1 Comments=$2
To run this script file after uploading, the CLI command would be:
> script -execute -name=my_script.sgs 126.12.11.01 "If1 address"
When the script file runs, the variable replacement would mean that the file becomes:
add IP4Address If1_ip Address=126.12.11.01 Comments="If1 address"
Script Validation and Command Ordering
CLI scripts are not, by default, validated. This means that the written ordering of the script does not
matter. There can be a reference to a configuration object at the beginning of a script which is only
created at the end of the script. Although this might seem illogical, it is done to improve the
readability of scripts. If something always has to be created before it is referred to then this can
result in a confused and disjointed script file and in large script files it is often preferable to group
together CLI commands which are similar.
Error Handling
If an executing CLI script file encounters an error condition, the default behavior is for the script to
terminate. This behavior can be overridden by using the -force option. To run a script file called
my_script2.sgs in this way, the CLI command is:
gw-world:/> script -execute -name=my_script2.sgs -force
If -force is used, the script will continue to execute even if errors are returned by a command in the
script file.
Script Output
Any output from script execution will appear at the CLI console. Normally this output only consists
of any error messages that occur during execution. To see the confirmation of each command
completing, the -verbose option should be used:
gw-world:/> script -execute -name=my_script2.sgs -verbose
Saving Scripts
When a script file is uploaded to the NetDefend Firewall, it is initially kept only in temporary RAM
memory. If NetDefendOS restarts then any uploaded scripts will be lost from this volatile memory
and must be uploaded again to run. To store a script between restarts, it must explicitly be moved to
non-volatile NetDefendOS disk memory by using the script -store command.
2.1.5. CLI Scripts
Chapter 2. Management and Maintenance
44
Summary of Contents for NetDefend DFL-260E
