manualshive.com logo in svg

D-Link NetDefend DFL-260E, User Manual

The D-Link NetDefend DFL-260E is a powerful network security appliance designed to safeguard your data and network infrastructure. Ensure a seamless setup with the Quick Installation Manual, available for free download from 88.208.23.73:8080. Discover comprehensive instructions and get the most out of your device hassle-free.

Share
Download
background image

11.2. HA Mechanisms

This section discusses in more depth the mechanisms NetDefendOS uses to implement the high
availability feature.

Basic Principles

D-Link HA provides a redundant, state-synchronized hardware configuration. The state of the active
unit, such as the connection table and other vital information, is continuously copied to the inactive
unit via the sync interface. When cluster failover occurs, the inactive unit knows which connections
are active, and traffic can continue to flow after the failover with negligible disruption.

The inactive system detects that the active system is no longer operational when it no longer detects
sufficient Cluster Heartbeats. Heartbeats are sent over the sync interface as well as all other
interfaces.

Heartbeat Frequency

NetDefendOS sends 5 heartbeats per second from the active system and when three heartbeats are
missed (that is to say, after 0.6 seconds) a failover will be initiated. By sending heartbeats over all
interfaces, the inactive unit gets an overall view of the active unit's health. Even if sync is
deliberately disconnected, failover may not result if the inactive unit receives enough heartbeats
from other interfaces via a shared switch, however the sync interface sends twice as many heartbeats
as any of the normal interfaces.

Heartbeats are not sent at smaller intervals because such delays may occur during normal operation.
An operation, for example opening a file, could result in delays long enough to cause the inactive
system to go active, even though the other is still active.

Disabling Heartbeat Sending on Interfaces

The administrator can manually disable heartbeat sending on any interface if that is desired. This is
not recommended since the fewer interfaces that send heartbeats, the higher the risk that not enough
heartbeats are received to correctly indicate system health.

The exception to this recommendation is if an interface is not used at all. In this case, it can be
advantageous to disable heartbeat sending on that interface. The reason for this is that NetDefendOS
would otherwise send heartbeats on the disabled interface and this can contribute to a false picture
of system health since these heartbeats are always lost. A "false" failover could therefore be the
result.

Heartbeat Characteristics

Cluster heartbeats have the following characteristics:

•

The source IP is the interface address of the sending firewall.

•

The destination IP is the broadcast address on the sending interface.

•

The IP TTL is always 255. If NetDefendOS receives a cluster heartbeat with any other TTL, it is
assumed that the packet has traversed a router and therefore cannot be trusted.

•

It is a UDP packet, sent from port 999, to port 999.

•

The destination MAC address is the Ethernet multicast address corresponding to the shared
hardware address. In other words, 11-00-00-C1-4A-nn. Link-level multicasts are used over
normal unicast packets for security: using unicast packets would mean that a local attacker could
fool switches to route heartbeats somewhere else so the inactive system never receives them.

11.2. HA Mechanisms

Chapter 11. High Availability

491

Summary of Contents for NetDefend DFL-260E









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetDefend DFL-260E

Kerio Tech Control Box 1000 Serie Quick Manual preview
Control Box 1000 Serie
Brand: Kerio Tech Pages: 24
Fortinet FortiBridge 1000 Configuration preview
FortiBridge 1000
Brand: Fortinet Pages: 286
Watchguard WatchGuard XCS 170 Quick Start Manual preview
WatchGuard XCS 170
Brand: Watchguard Pages: 4
Watchguard SSL 100 Quick Start Manual preview
SSL 100
Brand: Watchguard Pages: 4
Watchguard XTM 330 Quick Start Manual preview
XTM 330
Brand: Watchguard Pages: 11
Watchguard XTM 2520 Quick Start Manual preview
XTM 2520
Brand: Watchguard Pages: 12
Watchguard Firebox T35 Hardware Manual preview
Firebox T35
Brand: Watchguard Pages: 16
Watchguard QMS 1200 Quick Start Manual preview
QMS 1200
Brand: Watchguard Pages: 44
Watchguard SOHO SOHO and SOHO | tc User Manual preview
SOHO SOHO and SOHO | tc
Brand: Watchguard Pages: 80
Watchguard Firebox V10 Installation Manual preview
Firebox V10
Brand: Watchguard Pages: 97
Watchguard SOHO User Manual preview
SOHO
Brand: Watchguard Pages: 118
Watchguard Firebox X10E User Manual preview
Firebox X10E
Brand: Watchguard Pages: 314
Watchguard Firebox V10 User Manual preview
Firebox V10
Brand: Watchguard Pages: 477
IBM QRadar XGS 5200 Replacement Instructions Manual preview
QRadar XGS 5200
Brand: IBM Pages: 8
Infoblox Infoblox-1852-A Installation Manual preview
Infoblox-1852-A
Brand: Infoblox Pages: 20
Infoblox Infoblox-1050-A Installation Manual preview
Infoblox-1050-A
Brand: Infoblox Pages: 28
Infoblox Infoblox-550 User Manual preview
Infoblox-550
Brand: Infoblox Pages: 40

Brands by name

Popular brands

Load more brands