xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
108
0-7>] | counter [enable | disable]} | mirror {group_id <value 1-4>} | deny] {time_range
<range_name 32>} | delete access_id <value 1-256>]
Parameters
profile_id
- Specify the index of the access list profile.
<value 1-6>
- Enter the profile ID value here. This value must be between 1 and 6. A lower
value denotes a higher priority.
profile_name
- Specify the name of the profile.
<name 1-32>
- Enter the profile name here. This name can be up to 32 characters long.
add
access_id
- Specify to add the access ID. The value is from 1 to 256, but the supported
maximum number of entries depends on the project. If the auto_assign option is selected, the
access ID is automatically assigned, when adding multiple ports.
auto_assign
- Specify that the access ID will automatically be assigned.
<value 1-256>
- Enter the access ID used here. This value must be between 1 and 256. A
lower value denotes a higher priority.
ethernet
- Specify to configure the ethernet access profile.
vlan
- (Optional) Specify the VLAN name.
<vlan_name 32>
- Enter the name of the VLAN here. This name can be up to 32
characters long.
vlan_id
- (Optional) Specify the VLAN ID used.
<vlanid 1-4094>
- Enter the VLAN ID used here. This value must be between 1 and 4094.
mask
- (Optional) Specify an additional mask parameter that can be configured.
<hex 0x0-0x0fff>
- Enter the mask value here.
source_mac
- (Optional) Specify the source MAC address.
<macaddr>
- Enter the source MAC address used for this configuration here.
mask
- (Optional) Specify an additional mask parameter that can be configured.
<macmask>
- Enter the source MAC mask used here.
destination_mac
- (Optional) Specify the destination MAC address.
<macaddr>
- Enter the destination MAC address used for this configuration here.
mask
- (Optional) Specify an additional mask parameter that can be configured.
<macmask>
- Enter the destination MAC mask here.
802.1p
- (Optional) Specify the value of the 802.1p priority tag. The priority tag ranges from 1
to 7.
<value 0-7>
- Enter the 802.1p priority tag value here.
ethernet_type
- (Optional) Specify the Ethernet type.
<hex 0x0-0xffff>
- Enter the Ethernet type mask here.
ip
- Specify to configure the IP access profile.
vlan
- (Optional) Specify a VLAN name.
<vlan_name 32>
- Enter the name of the VLAN here. This name can be up to 32
characters long.
vlan_id
- (Optional) Specify that VLAN ID used.
<vlanid 1-4094>
- Enter the VLAN ID used here. This value must be between 1 and 4094.
mask
- (Optional) Specify an additional mask parameter that can be configured.
<hex 0x0-0x0fff>
- Enter the mask value here.
source_ip
- (Optional) Specify an IP source address.
<ipaddr>
- Enter the source IP address used for this configuration here.
mask
- (Optional) Specify an additional mask parameter that can be configured.
<netmask>
- Enter the source netmask used here.
destination_ip
- (Optional) Specify an IP destination address.
<ipaddr>
- Enter the destination IP address used for this configuration here.
mask
- (Optional) Specify an additional mask parameter that can be configured.
<netmask>
- Enter the destination netmask used here.
dscp
- (Optional) Specify the value of DSCP. The DSCP value ranges from 0 to 63.
<value>
- Enter the DSCP value here.
icmp
- (Optional) Specify to configure the ICMP parameters.
type
- (Optional) Specify that the rule will apply to the ICMP Type traffic value.
<value 0-255>
- Enter the ICMP type traffic value here. This value must be between 0
Summary of Contents for xStack DGS-3120 Series
