manualshive.com logo in svg

D-Link xStack DGS-3120 Series, Cli Reference Manual

The D-Link xStack DGS-3120 Series is a cutting-edge networking solution equipped with advanced features. Easily understand its capabilities and configuration options by downloading the comprehensive "Reference Manual". Find the free manual at 88.208.23.73:8080 and unlock the full potential of your D-Link xStack DGS-3120 Series with just a click.

Share
Download
background image

xStack

® 

DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide 

109 

 

and 255. 

code

 - Specify that the rule will apply to the ICMP Code traffic value. 

<value 0-255>

 - Enter the ICMP code traffic value here. This value must be between 0 

and 255. 

igmp

 - (Optional) Specify to configure the IGMP parameters. 

type

 - (Optional) Specify that the rule will apply to the IGMP Type traffic value. 

<value 0-255>

 - Enter the IGMP type traffic value here. This value must be between 0 

and 255. 

tcp

 - (Optional) Specify to configure the TCP parameters. 

src_port

 - (Optional) Specify that the rule will apply to a range of TCP source ports. 

<value 0-65535>

 - Enter the TCP source port value here. This value must be between 

0 and 65535. 

mask

 - (Optional) Specify an additional mask parameter that can be configured. 

<hex 0x0-0xffff>

 - Enter the source port mask here. 

dst_port

 - (Optional) Specify that the rule will apply to a range of TCP destination ports. 

<value 0-65535>

 - Enter the TCP destination port value here. This value must be 

between 0 and 65535. 

mask

 - (Optional) Specify an additional mask parameter that can be configured. 

<hex 0x0-0xffff>

 - Enter the destination port mask here. 

flag

 - (Optional) Specify the TCP flag fields. 

all

 - Specify that all the TCP flags will be used in this configuration. 

urg

 - (Optional) Specify that the TCP flag field will be set to 'urg'. 

ack

 - (Optional) Specify that the TCP flag field will be set to 'ack'. 

psh

 - (Optional) Specify that the TCP flag field will be set to 'psh'. 

rst

 - (Optional) Specify that the TCP flag field will be set to 'rst'. 

syn

 - (Optional) Specify that the TCP flag field will be set to 'syn'. 

fin

 - (Optional) Specify that the TCP flag field will be set to 'fin'. 

udp

 - (Optional) Specify to configure the UDP parameters. 

src_port

 - (Optional) Specify the UDP source port range. 

<value 0-65535>

 - Enter the UDP source port value here. This value must be between 

0 and 65535. 

mask

 - (Optional) Specify an additional mask parameter that can be configured. 

<hex 0x0-0xffff>

 - Enter the source port mask here. 

dst_port

 - (Optional) Specify the UDP destination port range. 

<value 0-65535>

 - Enter the UDP destination port value here. This value must be 

between 0 and 65535. 

mask

 - (Optional) Specify an additional mask parameter that can be configured. 

<hex 0x0-0xffff>

 - Enter the destination port mask here. 

protocol_id

 - (Optional) Specify that the rule will apply to the value of IP protocol ID traffic. 

<value 0-255>

 - Enter the protocol ID used here. 

user_define

 - (Optional) Specify that the rule will apply to the IP protocol ID and that the 

mask options behind the IP header , which has a length of 20 bytes. 

<hex 0x0-0xffffffff>

 - Enter the user-defined mask value here. 

mask

 - (Optional) Specify an additional mask parameter that can be configured. 

<hex 0x0-0xffffffff>

 - Enter the mask value here. 

packet_content

 - A maximum of 11 offsets can be specified. Each offset defines 2 bytes of data 

which is identified as a single UDF field. The offset reference is also configurable. It can be 
defined to start at the end of the tag, the end of the ether type or the end of the IP header. To 
qualify the fields before the end of the tag, the destination address, source address, and the 
VLAN tags are also included 

offset_chunk_1

 – (Optional) Specify the value of the packet bytes to be matched. Offset 

chunk 1 will be used. 

<hex 0x0-0xffffffff>

 - Enter the offset chunk 1 mask here. 

offset_chunk_2

 - (Optional) Specify the value of the packet bytes to be matched. Offset 

chunk 2 will be used. 

<hex 0x0-0xffffffff>

 - Enter the offset chunk 2 mask here. 

offset_chunk_3

 - (Optional) Specify the value of the packet bytes to be matched. Offset 

chunk 3 will be used. 

<hex 0x0-0xffffffff>

 - Enter the offset chunk 3 mask here. 

offset_chunk_4

 - (Optional) Specify the value of the packet bytes to be matched. Offset 

Summary of Contents for xStack DGS-3120 Series































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3120 Series

3onedata TNS5500D Series Quick Start Manual preview
TNS5500D Series
Brand: 3onedata Pages: 5
3onedata IPS7112G-4GS-8GPOE Quick Installation Manual preview
IPS7112G-4GS-8GPOE
Brand: 3onedata Pages: 3
Nectarine Health Satellite Manual preview
Satellite
Brand: Nectarine Health Pages: 9
Kramer VP-727XL User Manual preview
VP-727XL
Brand: Kramer Pages: 61
3onedata TNS5800-8GP16GT-P24VDC Quick Installation Manual preview
TNS5800-8GP16GT-P24VDC
Brand: 3onedata Pages: 3
Key Digital Champion KD-2X1 Operating Instructions Manual preview
Champion KD-2X1
Brand: Key Digital Pages: 12
LEGRAND C2G 29974 Manual preview
C2G 29974
Brand: LEGRAND Pages: 12
Optical Systems Design OSD2154P Operator'S Manual preview
OSD2154P
Brand: Optical Systems Design Pages: 20
WIKA PSM-700 Operating Instructions Manual preview
PSM-700
Brand: WIKA Pages: 8
IOGear GCS62DP Quick Start Manual preview
GCS62DP
Brand: IOGear Pages: 10
S+S Regeltechnik Premasreg 716 Series Operating Instructions, Mounting & Installation preview
Premasreg 716 Series
Brand: S+S Regeltechnik Pages: 32
Hama AV Selector 310 Operating Instruction preview
AV Selector 310
Brand: Hama Pages: 21
Exsys EX-1195HMS Manual preview
EX-1195HMS
Brand: Exsys Pages: 14
Rocstor Y10A251-B1 User Manual preview
Y10A251-B1
Brand: Rocstor Pages: 2
SEKURYX CK4-HPD404C User Manual preview
CK4-HPD404C
Brand: SEKURYX Pages: 13
Trust SMART Home AWMR-230 User Manual preview
SMART Home AWMR-230
Brand: Trust Pages: 57
Ascent Communication Technology ACT AS2308S Quick Reference Manual preview
ACT AS2308S
Brand: Ascent Communication Technology Pages: 8
Novatek-electro PEF-320 Operating Manual preview
PEF-320
Brand: Novatek-electro Pages: 8

Brands by name

Popular brands

Load more brands