xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
803
hello_interval
– Specify the interval of issuing hello packets fo find neighboring routers.
<sec 0-18000>
- Enter the time between 0 and 18000 seconds. The default value is 30.
triggered_hello_delay
- Specify the maximum time, in seconds, before the router sends a
triggered PIM Hello message on the specified interface. A value of zero indicates that
triggered PIM6 Hello message should always be sent immediately.
<sec 0-60>
- Enter the time between 0 and 60 seconds. The default value is 5.
propagation_delay
- Specify the expected propagation delay between the PIM6 routers on this
network or link, in seconds.
<sec 0-32>
- Enter the time between 0 and 32 seconds. The default value is 1.
override_interval
- Specify the value for the router to insert into the Override_Interval field of the
LAN Prune Delay option in the PIM6 Hello messages it sends on this interface. When
overriding a prune, PIM6 routers pick random time duration up to the value of this object. The
more PIM6 routers that are active on a network, the more likely it is that the prune will be
overridden after a small proportion of this time has elapsed. The more PIM6 routers are active
on this network, the larger this object should be to obtain an optimal spread of prune override
latencies.
<sec 0-65>
- Enter the time between 0 and 65 seconds. The default value is 3.
jp_interval
- Specify the frequency at which this router sends PIM6 Join/Prune messages on this
PIM6 interface. A value of zero represents not to send PIM Join/Prune message on this
interface.
<sec 0-18000>
- Enter the time between 0 and 18000 seconds. The default value is 60.
dr_priority
- Specify the Designated Router Priority value inserted into the DR Priority option in
PIM6 Hello message transmitted on this interface. Numerically higher values for this
parameter indicate higher priorities.
<uint 0-4294967294>
- Enter the value between 0 and 4294967294. The default value is 1.
bsr_border
- Specify to determine whether this interface is a PIM6 domain border. If this
interface is a domain border, it prevents bootstrap router (BSR) messages from being sent or
received through it.
disable
- Specify that the interface is not a PIM6 domain border. This is the default.
enable
- Specify that the interface is a PIM6 domain border.
stub_interface
- Specify whether this interface is a stub interface. If this interface is a stub
interface, no PIM6 packets are sent out to this interface, and any received PIM6 packets are
ignored.
disable
- Specify that the interface is not a stub interface. This is the default.
enable
- Specify that the interface is a stub interface.
state
- Specify to allow the PIM6 to be disabled or enabled for the IPv6 interface.
enable
- Enable PIM6 for the IPv6 interface.
disable
- Disable PIM6 for the IPv6 interface.
Restrictions
Only Administrator, Operator and Power-User level users can issue this command.
Example
To set the jp_interval to 60 seconds, the hello_interval to 60 seconds, and enable the PIM6 state
for interface “System”:
DGS-3120-24TC:admin#config pim6 ipif System jp_interval 60 hello_interval 60
state enable
Command: config pim6 ipif System jp_interval 60 hello_interval 60 state enable
Success.
DGS-3120-24TC:admin#
Summary of Contents for xStack DGS-3120 Series
