background image

 

 

 

 

 
 

 
 
 
 

The lightning flash with an arrowhead symbol, within an equilateral 

triangle is intended to alert the user to the presence of uninsulated 

dangerous voltage within the product's enclosure that may be of 

sufficient magnitude to constitute a risk of electric shock to persons. 

 

The exclamation point within an equilateral triangle is intended to alert 

the user to the presence of important operating and maintenance 

(servicing) instructions in the literature accompanying the appliance. 

 

INFORMATION - 

This equipment has been tested and found to comply with limits for a 

Class A digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference 

when the equipment is operated in a commercial environment. 

This equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instruction manual, may cause 

harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful interference in 

which case the user will be required to correct the interference at his own expense. 

 

WARNING - 

Changes or modifications not expressly approved by the 

manufacturer could void the user’s authority to operate the equipment. 

CAUTION : 

To prevent electric shock and risk of fire hazards: 

Do NOT use power sources other than that specified. 

Do NOT expose this appliance to rain or moisture.

 

 

This installation should be made by a qualified service person and should conform 

to all local codes

 

 

Summary of Contents for DCC 600d Series






















Reviews: