background image

17 

MAINTENANCE 

It is very important to periodically clean your 

RedHead 

RH  300

 

system  for  maximum  performance.    Regular 

cleaning will also lengthen the life of your unit. 

  

• 

Clean  the 

RedHead  RH  300 

collar  box  with 

lukewarm water and a mild anti-bacterial soap. 

• 

Take  care  to  thoroughly  clean  the  space  between 
the Contacts and the Collar Belt. 

• 

The  belt  and  buckle  should  be  cleaned  with  water 
and a mild soap and then allowed to dry completely. 

• 

Always allow the entire unit to completely dry before  
using. 

NOTE 

It is recommended that the collar unit  be rinsed  with fresh, 
clean  water  after  use  in  wet  conditions,  especially  in  salt 
water.

 

To get the maximum performance and life out of your 
batteries: 

  

• 

Use  your  collar  system  in  the  Battery  Saving  Mode 
when 

an 

instantaneous 

response 

to 

your 

Transmitter is not required. 

• 

Do  not  store  your  unit  in  extremely  hot  or  cold 
conditions. 

• 

Store your unit in a dry environment. 

• 

Remove  the  batteries  when  storing  your  unit  for 
extended periods of time. 

Summary of Contents for RedHead RH 300





















Reviews: