background image

LIMITED FIVE YEAR WARRANTY ON DA-LITE DESCENDER PRO PRODUCTS ONLY

Milestone AV Technologies LLC warrants these Da-Lite branded products to the original purchaser only, to be free from defects in materials and 
workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according 
to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, 
or which has been tampered with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. Returns 
for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses 
to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment. 

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. 

Any implied warranties of fitness for use, or 

merchantability, that may be mandated by statute or rule of law are limited to the five (5) year warranty period. This warranty gives you specific 
legal rights, and you may also have other rights, which vary from state-to-state. 

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE 

LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT, 
OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at 3100 
North Detroit Street, Warsaw, IN 46582, (574) 267-8101, (800) 622-3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS 
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

FOR YOUR IMAGE  |  legrandav.com

USA P

 866.977.3901 

E

 info@da-lite.com 

CANADA P

 877.345.4329 

canadainfo@milestone.com 

EMEA P

 +31 495 580 840 

E

 emea.sales@milestone.com 

APAC P 

+852 2145 4099 

asia.da-lite@milestone.com

In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone AV Technologies ULC. 
©2018 Milestone AV Technologies. DL–0731 (Rev. 1) 11/18 Da-Lite is a registered trademark of Milestone AV 
Technologies. All other brand names or marks are used for identification purposes and are trademarks of 
their respective owners. All patents are protected under existing designations. Other patents pending. 

Summary of Contents for DescenderPro













Reviews: