background image

2

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1. 

Read and understand all instructions before using.

2.  Close supervision is necessary when any appliance is used by 

or near children. Do not leave appliance unattended while in 
use.

3.  Do not operate appliance with a damaged cord or if the 

appliance has been dropped or damaged – until it has been 
examined by a qualified serviceman.

 4.  Position the cord so that it will not be tripped over, pulled, or 

contact hot surfaces.

5.  If an extension cord is necessary, a cord with a current rating 

at least equal to that of the appliance should be used. Cords 
rated for less amperage than the appliance may overheat.

6.  To reduce the risk of electric shock, do not immerse this 

appliance in water or other liquids.

7. 

To reduce the risk of electric shock, do not disassemble this 
appliance. Contact an authorized service dealer when repair 
work is required. Incorrect reassembly can cause electric 
shock when the appliance is used subsequently.

8.  The use of an accessory attachment not recommended by 

the manufacturer may cause a risk of fire, electric shock, or 
injury to persons.

Save These Instructions

Summary of Contents for LARGE ADVANTAGE DELUXE ELECTROL













Reviews: