Da-Lite LARGE ADVANTAGE DELUXE ELECTROL Instruction Book Download

Page: 3 / 12

Tools Required for Installation

Pre-Installation

#2 Phillips Screwdriver

3/4“ Open Wrench

or Socket Driver

1. Carefully unpack case from shipping crate.

2. Set aside the Installation Kit. Items inside will be used during

installation.

3. Make sure to recheck measurement of case for proper

installation clearance.

4. Remove any protective foam from case.

5. If necessary. adjust hanger brackets with a 3/4" open wrench

or socket driver.

Ironing Board

The Large Advantage Electrol includes an ironing board to flatten

the fabric (long strip attached). The ironing board is part of the
screen case. Do not remove. Contact Da-Lite if the ironing board
is in need of adjustment. (Figure 1).

Ironing
Board

Figure 1

Summary of Contents for LARGE ADVANTAGE DELUXE ELECTROL













Search results

Summary of Contents for LARGE ADVANTAGE DELUXE ELECTROL

Reviews:

Related manuals for LARGE ADVANTAGE DELUXE ELECTROL

Brands by name

Popular brands

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL, Instruction Book

Search results

Summary of Contents for LARGE ADVANTAGE DELUXE ELECTROL

Reviews:

Related manuals for LARGE ADVANTAGE DELUXE ELECTROL

Brands by name

Popular brands