Da-Lite MULTI-MASK IMAGER Instruction Book Download

Page: 5 / 12

FIGURE 5

ELECTRICAL WIRING

Electrical wiring is required for each mask roller motor. The vertical masking systems have one motor at the frame top.
Horizontal masking systems have one motor at the frame top and one at the bottom.

A motor requires standard 120V/220V input. All connections are made to the electrical box on the audience left side of
the unit.

FIGURE 6

SPRING TENSION CABLE

EYE SNAP

EYELET

HORIZONTAL MASK CONNECTION

VERTICAL MASK CONNECTION

HORIZONTAL MASK CONNECTION

SLAT

SURFACE

TAPE STRIP

Tensioning the bottom masking panel

1. Carefully remove all tape strips securing surfaces around rollers. Slats should move freely. See Figure 5.

2. Locate the spring tension cables on either side of the unit.

3. Connect the eye snap to the eyelet on the bottom masking panel bar. See Figure 5. You will need to pull the cable

slightly.

4. Repeat for the other side.

SLAT

Summary of Contents for MULTI-MASK IMAGER













Search results

Summary of Contents for MULTI-MASK IMAGER

Reviews:

Related manuals for MULTI-MASK IMAGER

Brands by name

Popular brands

Da-Lite MULTI-MASK IMAGER, Instruction Book

Search results

Summary of Contents for MULTI-MASK IMAGER

Reviews:

Related manuals for MULTI-MASK IMAGER

Brands by name

Popular brands