DAB e.sybox Series Manual Download

Page: 30 / 54

ENGLISH

7.4.1 - Status:

Displays the pump status.

7.4.2 - RI: Speed setting

Sets the motor speed in rpm. Allows you to force the number of revolutions

at a predetermined value.

7.4.3 - VP: Pressure display

Plant pressure measured in [bar] or [psi] depending on the measuring sys

tem used.

7.4.4 - VF: Flow display

Displays the flow in the chosen unit of measure. The measuring unit may

be [l/min] o [gal/min] vedi par. 7.5.4 - MS: Measuring system.

7.4.5 - PO: Absorbed power display

Power absorbed by the electropump in [kW].

A flashing round symbol may appear under the symbol of the measured

power PO. This symbol indicates the pre-alarm for exceeding the allowed

maximum power.

7.4.6 - C1: Phase current display

Motor phase current in [A].

A flashing round symbol may appear under the symbol of the phase cur

rent C1. This symbol indicates the pre-alarm for exceeding the allowed

maximum current. If it flashes at regular intervals it means that the motor

overload protection is about to trip and it will very probably go into protec

tion status.

7.4.7 - RS: Rotation speed display

Motor rotation speed in rpm.

7.4.8 - TE: Dissipator temperature display

7.5 - Installer Menu

From the main menu, hold down simultaneously the “MODE” and “SET”

and “-“ keys until the first parameter of the installer menu appears on the

display (or use the selection menu pressing + or -). The menu allows

you to view and modify various configuration parameters: the MODE key

allows you to scroll through the menu pages, the + and – keys allow you re

spectively to increase and decrease the value of the parameter concerned.

Press SET to leave this menu and return to the main menu.

7.5.1 - RP: Setting the pressure fall to restart

Expresses the fall in pressure with respect to the SP value which causes

restarting of the pump.

For example if the setpoint pressure is 3.0 [bar] and RP è 0.5 [bar] the

pump will restart at 2.5 [bar].

RP can be set from a minimum of 0.1 to a maximum of 1 [bar]. In particular

conditions (for example in the case of a setpoint lower than the RP) it may

be limited automatically.

To assist the user, on the RP setting page the actual restarting pressure

also appears highlighted under the RP symbol, see Figure 17

also appears highlighted under the RP symbol, see Figure 17..

7.5.2 - OD: Type of plant

VPossible values 1 and 2 referring to a rigid system and an elastic system.

The device leaves the factory with mode 1 suitable for the majority of sys

tems. In the presence of swings in pressure that cannot be stabilised by

adjusting the parameters GI and GP, change to mode 2.

Figura 17: Setting the restart pressure

IMPORTANT:

The regulating parameters GP and GI also change in

the two configurations. In addition the GP and GI values set in mode

1 are stored in a different memory from the GP and GI values set in

mode 2. So, for example, when passing to mode 2, the GB value of

mode 1 is replaced by the GB value of mode 2 but it is kept and will

reappear again when returning to mode 1. The same value shown on

the display has a different weight in one mode or in the other because

the control algorithm is different.

Summary of Contents for e.sybox Series























































Search results

Summary of Contents for e.sybox Series

Reviews:

Related manuals for e.sybox Series

Brands by name

Popular brands

DAB e.sybox Series, Manual

Search results

Summary of Contents for e.sybox Series

Reviews:

Related manuals for e.sybox Series

Brands by name

Popular brands