background image

ENGLISH

60

GB

and working conditions, have been approved by the person in 

and working conditions, have been approved by the person in 

charge of plant safety, authorizing them to perform all the neces

-

charge of plant safety, authorizing them to perform all the neces

-

sary activities, during which they are able to recognize and avoid 

sary activities, during which they are able to recognize and avoid 

all dangers. (Definition for technical personnel IEC 364).

all dangers. (Definition for technical personnel IEC 364).

The products dealt with in this discussion fall within the type of 

The products dealt with in this discussion fall within the type of 

professional equipment and belong to insulation class 1.

professional equipment and belong to insulation class 1.

It 

It 

is the responsibility of the installer to make sure that the power 

is the responsibility of the installer to make sure that the power 

supply  system  is  equipped  with  an  efficient  grounding  system 

supply  system  is  equipped  with  an  efficient  grounding  system 

according to the regulations in force.

according to the regulations in force.
To  improve  immunity  to  possible  noise  radiating  to  other 

To  improve  immunity  to  possible  noise  radiating  to  other 

equipment, it is advisable to use separate wiring to power the 

equipment, it is advisable to use separate wiring to power the 

inverter.

inverter.
The appliance is not intended to be used by persons (including 

The appliance is not intended to be used by persons (including 

children) with reduced physical, sensory or mental capacities, or 

children) with reduced physical, sensory or mental capacities, or 

who lack experience or knowledge, unless, through the media

-

who lack experience or knowledge, unless, through the media

-

tion of a person responsible for their safety, they have had the 

tion of a person responsible for their safety, they have had the 

benefit of supervision or of instructions on the use of the appli

-

benefit of supervision or of instructions on the use of the appli

-

ance. Children must be supervised to ensure that they do not 

ance. Children must be supervised to ensure that they do not 

play with the appliance. 

play with the appliance. 

Safety

Safety

Use is allowed only if the electric system is in possession of safe

-

Use is allowed only if the electric system is in possession of safe

-

ty precautions in accordance with the regulations in force in the 

ty precautions in accordance with the regulations in force in the 

country where the product is installed (for Italy CEI 64/2).

country where the product is installed (for Italy CEI 64/2).
Pumped liquids

Pumped liquids

The machine has been designed and made for pumping water, 

The machine has been designed and made for pumping water, 

free from explosive substances and solid particles or fibres, with 

free from explosive substances and solid particles or fibres, with 

a density of 1000 Kg/m³, a kinematic viscosity of 1mm²/s and 

a density of 1000 Kg/m³, a kinematic viscosity of 1mm²/s and 

non chemically aggressive liquids.

non chemically aggressive liquids.
The power supply cable must never be used to carry or shift the 

The power supply cable must never be used to carry or shift the 

pump.

pump.

KEY 

KEY 

The following symbols have been used in the discussion:

The following symbols have been used in the discussion:

S

ituation of general danger. Failure to respect the instruc

-

tions that follow may cause harm to persons and property.

Situation of electric shock hazard. Failure to respect the 

instructions that follow may cause a situation of grave risk for 

personal safety.

Notes

WARNINGS

WARNINGS

This manual refers to e.sybox products. In the following discussion, the 

This manual refers to e.sybox products. In the following discussion, the 

term  e.sybox  will  be  used  when  the  characteristics  are  shared  by  both 

term  e.sybox  will  be  used  when  the  characteristics  are  shared  by  both 

models. If the characteristics differ, the models and their differences will 

models. If the characteristics differ, the models and their differences will 

be specified.

be specified.

R

R

ead this documentation carefully before installation. 

ead this documentation carefully before installation. 

Installation and operation must comply with the local safety reg

-

Installation and operation must comply with the local safety reg

-

ulations in force in the country in which the product is installed. 

ulations in force in the country in which the product is installed. 

Everything must be done in a workmanlike manner.

Everything must be done in a workmanlike manner.

Failure to respect the safety regulations not only causes risk to 

Failure to respect the safety regulations not only causes risk to 

personal safety and damage to the equipment, but invalidates 

personal safety and damage to the equipment, but invalidates 

every right to assistance under guarantee.

every right to assistance under guarantee.

Skilled personnel

Skilled personnel
T

T

he electrical and hydraulic connections may only be carried out 

he electrical and hydraulic connections may only be carried out 

by skilled personnel in possession of the technical qualifications 

by skilled personnel in possession of the technical qualifications 

required by the safety regulations in force in the country in which 

required by the safety regulations in force in the country in which 

the product is installed.

the product is installed.

The term skilled personnel means persons whose training, ex

-

The term skilled personnel means persons whose training, ex

-

perience and instruction, as well as their knowledge of the re

-

perience and instruction, as well as their knowledge of the re

-

spective  standards  and  requirements  for  accident  prevention 

spective  standards  and  requirements  for  accident  prevention 

Summary of Contents for e.sybox Series























































Reviews: