3
Planning the Installation
WARNING
IMPORTANT:
Observe all governing codes and ordinances
during planning and installation. Contact your local building
department for further information.
The appliance installation must be electrically grounded in
accordance with local codes or, in the absence of local codes,
with the National Electrical Code, ANSI/ NFPA 70:
Electrical Requirements - All Model
Numbers Except -C Models)
•
It is the owner’s responsibility to ensure that the electrical
connection of this appliance is performed by a licensed
electrician.
•
The correct voltage, frequency and amperage must be
supplied to the appliance from a separate, grounded, circuit
that is protected by a properly sized circuit breaker or time
delay fuse. If a fuse is utilized, fuse both sides of the line (L1
and L2).
Model
Circuit Required
Total
Connected
Load
DYRP36Dx
240 Vac*, 60 Hz, 30 Amp.
5.75 kW
(24.0 Amp.)
DYRP48Dx
240 Vac*, 60 Hz, 50 Amp.
10.1 kW
(41.9 Amp.)
* 4-wire, two 120 Vac hot (L1 and L2), one neutral, one ground
The ratings above are for reference only. Refer to the range data
label for exact specifications (see inside cover for location).
•
The wiring needs to be long enough to allow the range to be
pulled out for service, while remaining connected.
•
The wiring to the range must:
◊
Meet NEMA standards and have a minimum rating of
250 Volts @ 30 Amps for model DYRP36D[C/S] and 250
Volts @ 50 amps for model DYRP48[C/S]
◊
Include a strain relief
◊
Be terminated by tinned leads, closed loop terminals or
open ended spade lugs with upturned ends
◊
Connect to a junction box or receptacle installed by a
licensed electrician
The appliance may be connected one of the following ways:
•
Using conduit:
◊
A 4-wire conduit connected to a 4-wire junction box, or
◊
A 3-wire conduit (where local code permits, not for use
with new branch circuit installations) connected to a
3-wire junction box.
Suggested wiring color code: Black, white, red and green.
•
Using an appliance cord:
◊
A 4-wire appliance cord equipped with a NEMA 14-50P
plug connected to a NEMA 14-50R receptacle, or
◊
A 3-wire appliance cord (where local code permits)
equipped with a NEMA 10-50P plug connected to a
NEMA 10-50R receptacle
◊
Appliance cord plug must be UL listed type SRD or
SRDT.
Electrical Requirements
-C Model Numbers
Range models DYRP36D-C-[C/S] and DYRP48D-C-[C/S] come
with a factory installed 4-wire appliance cord with NEMA 14-50P
plug.
•
For freestanding ranges installed in Canada, a factory
installed 4-wire appliance cord with NEMA 14-50P plug is
required, without modification.
•
The NEMA 14-50P plug is designed to plug directly into
a NEMA 14-50R electrical receptacle. It is the owner’s
responsibility to ensure that the required 4-wire electrical
outlet compatible with the power cord is installed by a
licensed electrician as specified below prior to range
installation. The electrical outlet installation, including
minimum supply wire size and grounding, must be in
accordance with all governing codes and ordinances.
•
The correct voltage, frequency and amperage must be
supplied to the appliance from a separate, grounded, circuit
that is protected by a properly sized circuit breaker or time
delay fuse. If a fuse is utilized, fuse both sides of the line (L1
and L2). Refer to the ratings on the range rating label.
Model
Circuit Required
Total
Connected
Load
DYRP36D-C-x
240 Vac*, 60 Hz, 30 Amp.
5.75 kW
(24.0 Amp.)
DYRP48D-C-x
240 Vac*, 60 Hz, 50 Amp.
10.1 kW
(41.9 Amp.)
* Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.
The ratings above are for reference only - refer to the range rating
label (see inside cover).
NEMA 10-50P Plug
NEMA 14-50P Plug
NEMA 14-50R Receptacle
NEMA 10-50R Receptacle
