background image

14

Installation Instructions

Install Exhaust Deflector

 CAUtION

Install the exhaust deflector before installing the oven 

door(s).

Attach the exhaust deflector to the front of the oven. It 

attaches to the oven just below the oven chamber in the 

door jam. On a double oven, the exhaust deflector is 

mounted below the bottom oven chamber.
1.  Line up the mounting holes on the exhaust deflector 

with the screw holes on the front of the oven.

2.  Secure it using the three (3) screws provided.

Reinstall the Oven Door(s)

 WARNING

To avoid damage to the door or personal injury from it 

falling off its hinges:

• 

Make sure that the notch on the bottom of each hinge 

rests on top of the lower lip of each hinge receptacle 

before attempting to open the oven door.

• 

Rotate the hinge locks toward the front of the oven 

immediately and completely after installation of the 

door.

 CAUtION

On double ovens: Install the upper door first to prevent 

damage to the lower door.

1.  Grasp the oven door on opposite sides and hold it at a 

15° angle from the front of the oven. See facing page. 

2.  Slide the hinges into the hinge openings, resting the 

bottom of the hinge arms on the hinge receptacles. 

3.  Continue to hold the door at a 15° angle with one hand 

while pushing in on each of the bottom corners of the 

door. Push until the notch on the bottom of each hinge 

slips over the lower lip of each hinge receptacle.

4.  Lower the door to the fully opened position.
5.  Rotate the two hinge locks toward the oven. Slowly and 

carefully open and close the door completely to make 

sure that it is properly installed.

Verify Proper Operation

 WARNING

Read the accompanying use and care manual completely 

before using the oven.

1.  Remove any packaging from inside the oven(s).
2.  On some models there is protective plastic coating over 

the stainless steel surfaces. Peel them off before use.

3.  Slide the oven racks onto the support racks in the oven 

chamber(s) as instructed in the use and care manual.

4.  Turn on the power to the oven at the circuit breaker 

or fuse box. Set the clock as instructed in the use and 

care manual.

5.  Set the oven to bake mode as instructed in the use and 

care manual.

NOtES:

 If the oven does not operate properly, follow these 

troubleshooting steps:

• 

Verify that power is supplied to the oven.

• 

Check for proper electrical connection.

• 

Repeat the above bake test.

• 

If the appliance still does not work, contact Dacor

• 

Distinctive Service at (877) 337-3226. Do not attempt 

to repair the appliance yourself. If you need service, be 

sure to have the model and serial numbers available 

when you call. See page 3 for location.

Dacor is not responsible for the cost of correcting problems 

caused by a faulty installation.

Summary of Contents for Discovery EO127





















Reviews: