background image

Electrical Connection (cont.)

Connecting the Conduit to the House 

Electrical Junction Box

 WARNING

Do not ground the appliance to a gas supply pipe or hot 

water pipe.

Do not turn on power to the appliance until the range is 

permanently grounded.

A grounded cold water pipe must have metal continuity to 

electrical ground and must not be interrupted by insulating 

materials. Any insulating materials must be jumpered with a 

length of No. 4 copper wire securely clamped to bare metal 

at both ends.

NOTES:

The power supply must be properly polarized. Reverse 

polarity will result in continuous sparking of the electrodes, 

even after flame ignition.
If there is any doubt as to whether the power supply is 

properly polarized or grounded, have it checked by a licensed 

electrician.
With the range positioned directly in front of the cabinet 

cutout, feed the appliance wires into the junction box. 

Depending upon local codes, utilize one of the three (3) 

methods shown to connect the appliance to the junction box.
Connect the white wire from the appliance to the neutral 

(white) supply wire in the junction box.
Connect the black wire from the appliance to the black (L1) 

power supply wire in the junction box.
Connect the red wire from the appliance to the red (L2) 

power supply wire in the junction box.
If using a 4 wire connection, connect the green wire to a 

grounded supply wire in the junction box or to a grounded 

cold water pipe. If connecting to a grounded cold water pipe:

Replace the junction box cover.

1.

2.

3.

4.

5.

6.

Installation Instructions

Connection to 

power supply

Connection to 

appliance (Page 13)

Wire Nut, 

3 Places

Junction 

Box

3 Wire Connection Conduit 

Junction Box Connection

Connection to 

power supply

Connection to 

appliance (Page 13)

Wire Nut, 

4 Places

Junction 

Box

4 Wire Connection Conduit 

Junction Box Connection

Use a separate copper grounding wire (No. 10 minimum) 

to connect to the cold water pipe by means of a clamp 

and an external grounding connector screw. 
If there are any materials that isolate the cold water pipe 

from ground, jumper it with a No. 4 copper wire, clamped 

on both ends.

Summary of Contents for Epicure ER30DSCH

























Reviews: