13
Verifying Proper Operation
WARNING
Before operating the range, read the accompanying use
and care manual completely.
Before beginning the test procedure, make
1)
sure all range control valves are in the “
OFF”
position, and all burner rings, burner cap and
grates are properly positioned on the spill tray.
Turn on the gas supply at the shut-off valve.
2)
Connect the power cord to the electrical outlet. When
3)
the range is first connected, the oven indicator light
flashes on and off for about 10 seconds while the
range’s circuitry starts up. Wait for the light to stop
flashing before going to step 4.
Test the left front burner on the cooktop by pushing in
4)
and turning the control knob counterclockwise to the
HIGH
position. The knob should light when in the
“ON“
position. The igniter for the left front burner will spark
continuously. It may take up to 4 seconds for the burner
to ignite, at which time the ignitor will stop sparking.
If ignition does not occur within 4 seconds, turn off
the knob, wait for at least 5 minutes to allow any gas
to dissipate, then repeat this ignition test. When the
burner ignites, rotate the knob counterclockwise from
HIGH
to
LOW
to adjust the flame height progressively.
When installed properly, the
flame will be steady. It will
also have a sharp, blue inner
cone that will vary in length
proportional to the burner size.
LP gas units may have small
yellow tips at the end of the
flames, which is normal.
Repeat the ignition test for the
5)
remaining cooktop burners.
Check to make sure the knobs light when in the
“ON”
position.
After testing all the cooktop burners, turn them all off.
6)
Open the oven door. Test the oven light by turning on
7)
the light switch on the right side of the control panel.
Turn on the convection fan switch. You should hear the
8)
convection fan, located behind the screen at the back
of the oven, come on.
With the oven door open, turn the oven control knob
9)
to the 400 degree position. Both the knob itself and
the oven ON indicator light next to the knob should
illuminate. Within 60 seconds you should hear the bake
burner ignite below the oven floor. It should begin to
give off heat.
Turn the oven control knob to the
10)
BROIL
position. The
bake burner should turn off. Both the oven control knob
and the oven ON indicator light should be illuminated.
Within 60 seconds the IR burner on the ceiling of the
oven should ignite and begin to give off heat.
Turn the oven knob to the “
11)
OFF”
position.
Installation Instructions
If the range does not operate properly, follow these
troubleshooting steps:
Verify that the circuit breaker for the range electrical
1)
outlet is on and not tripped. Make sure the power cord
is connected.
Make sure the gas supply valve is in the on position
2)
and that the main gas valve to the building is open.
Check to see if the oven burner light flashes on and
3)
off once a second. If it does, repair by an authorized
service technician is required.
Repeat the above tests.
4)
If the appliance still does not work, contact Dacor
5)
Distinctive Service at (877) 337-3226. Do not attempt to
repair the appliance yourself. Dacor is not responsible
for the cost of correcting problems caused by a faulty
installation.
Installation Checklist
WARNING
To ensure a safe and proper installation, the installer
must perform the following checklist to ensure that no
part of the installation has been overlooked. Proper
installation is the responsibility of the homeowner.
Has the plastic coating been peeled off of the outside
□
of the range? Have all packaging materials been
removed from inside the oven?
Are all leveling legs extended down to make contact
□
with the floor? Is the unit level? See page 8.
Is the range secured in place with the provided anti-tip
□
bracket and foot according to these instructions? See
page 9.
Is the range connected to a grounded three prong
□
electrical outlet that has been installed by a licensed
electrician according to these instructions and in
accordance with all applicable electrical codes? See
pages 4 and 5.
Is the backguard installed?
□
Has the gas supply inlet pressure been measured to
□
ensure that it does not exceed the maximums stated in
these instructions? See page 4.
Is the range connected to the gas supply according to
□
these instructions and in accordance with all applicable
codes? See pages 4 and 10.
Did the installer check the gas supply for leaks?
□
Is the oven door properly installed according to these
□
instructions? See page 11.
Are the burners and grates properly installed according
□
to these instructions? See page 12.
Has proper operation been verified?
□
Has the warranty been activated on-line or the warranty
□
card been filled out completely and mailed?
OFF
Normal Flame
