background image

IMPORTANT 

1.  Before beginning installation, please thoroughly read and become familiar with these instructions. 

2.  Installation and service must be completed by a qualified installer or service agency.

3.   Installer: Please leave these Installation Instructions with the owner.

4.   Owner: Please keep these instructions for local electrical inspector’s use and for future reference.

5.  Read the accompanying Use & Care Manual prior to operating this appliance.

TABLE OF CONTENTS

STEP  1  Package contents verification 

Page  2

STEP  2  Installation planning 

Page  2-4

STEP  3  Installing the support platform in the cabinet 

Page  5

STEP  4  Electrical power supply requirements 

Page  5

STEP  5  Removing the oven door(s) 

Page  5-6

STEP  6   Turning of the power supply 

Page  6

STEP  7   Electrical connection 

Page  6

STEP  8   Mounting the oven 

Page  7

STEP   9  Installing the exhaust deflector 

Page  7

STEP  10  Re-installing the oven door(s) 

Page  7

STEP  11  Installation check list 

Page  7

STEP  12  Verifying oven operation 

Page  8

Part No. 65433  Rev. C

TESTEd IN ACCORdANCE wITh ThE LATEST EdITION OF ANSI/UL 858 ANd CAN/CSA-C22.2 NO. 64 STANdARd 

FOR hOUSEhOLd ELECTRIC COOkINg ANd LIqUId hEATINg APPLIANCES.

NOTES: 

 

Contain helpful hints and tips to facilitate the installation.

CONVENTIONS USEd IN ThESE INSTRUCTIONS

wARNINgS:

 

Must be followed carefully to avoid personal injury or damage.

REAd ANd SAVE ThESE INSTRUCTIONS

Installation Instructions

wall Oven

Summary of Contents for Wall Oven













Reviews: