background image

4

ADJUSTMENTS

1.  TUNER SECTION

TEST EQUIPMENT

1.  Signal Generator with a frequency range of FM broadcast.
2.  Oscilloscope with a side amplifier of approximately 100 KHz.
3.  FM 75/50

 dummy antenna.

4.  VTVM

FM ALIGNMENT

1.  Turn on the FM signal generator and the VTVM allowing 15 minutes warming-up period.
2.  Connect the VTVM across the headphone jack or speaker terminal.
3.  Set signal generator frequency as listed in ALIGNMENT CHART and maintain a sufficient output level to provide an

indication on VTVM.

NOTE

1. Use a screwdriver with plastic or ceramic grip for all adjustments.
2. Standard test frequency 1 KHz and deviation 75 KHz for FM.

 - FM RF, IF ALIGNMENT CHART - 

Unless other specified set being switched FM mode, adjust generator's frequency to center of the FM band where no FM broadcast exists
Otherwise adjustment of FM usable sensitivity, frequency range for FM band are not needed, but confirm these data are satisfied with specifi-
cation.
CAUTION : When realigning the FM receiving frequency the highest end of the frequency range should not be more than 108 MHz and the 
lowest end of the frequency range should not be less than 87.5 MHz, in order to comply with FTZ regulation in West Germany.

2. CD SECTION

Note:

 1. Use the oscilloscope with more than 10M

Ω 

impedance.

   2. Clean an object lens by an applicator with natural detergent when the signal level is lower than specified value

             with the following checks.

RF LEVEL CHECK

 1.  Connect oscilloscope to test point TP502 and IC502 

Pin66 on CD PCB.

 2.  Press power switch on.
 3.  Put test disc(TCD-781) in and press play button then 

pause button.

 4.  Confirm that oscilloscope waveform is clear. Clear 

RF signal waveform means that the shape"#"can be 
clearly distinguished at the center of waveform.

 5.  Adjust RV501 to get a clear waveform and maximum 

amplitude.

Step

Item

Input Circuit Setup Output Circuit Setup

Tuner Setting

Adjust Point

Adjustment

1

FM IF 

Adjustment

Connect stereo signal 

generator to FM ANT 

terminal (J001)

Connect DC voltme-

ter to edge R201

FM98MHz75KHz 

Dev. 26dB

µ

L203

Adjust forDC 0V

±

0.1V

2

Auto Stop 

Sensitivity

Connect stereo signal 

generator to FM ANT 

terminal (J001)

Connect DC voltme-

ter to edge of RV201

FM 98MHz 

75KHz Dev. 

26dB

µ

RV201

Adjust for DC 
1.17V

±

0.02V 

Confirm stereo indica-

tor is lighted and L/R 

channel is separated.

SET

FM Antenna

Terminal(75 ohm)

Carrier Frequency : 98MHz
Output Level : 26dBuV
Modulation:Audio 1kHZ, 75kHz Deviation

FM RF SSG

75 ohm Coaxal

Level : 1.2+0.3Vp-p

RF Signal Waveform

VOLT/DIV : 200mV

TIME/DIV : 50ns

All manuals and user guides at all-guides.com

Summary of Contents for AMI-921DP






























Reviews: