10
11
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY (CD/MP3/USB)
1. Rotate the TUN+/-&NEXT/PREV CONTROL shortly in music play to skip to the next track
or go back to beginning of the current track, rotate the TUN+/-&NEXT/PREV CONTROL
twice continuously to skip to the previous track.(While operating, it is necessary to
observe the silkscreen beside the TUN+/-&NEXT/PREV CONTROL for operating
correctly.)
2. Rotate and hold the TUN+/-&NEXT/PREV CONTROL in music play to search at quick
rate for a specific point to play.
3. Press the +10/ALBUM button once in play to skip to the track 10 tracks ahead, twice to
skip to the track 20 tracks ahead. You can reach the last track of the disc using this
button.
REPEAT PLAYBACK (CD/MP3/USB)
During playback, press the MODE/PROG/MEM button to repeat play a single track; press
the button twice to repeat play all tracks; press the button three times to enter the
introduction play mode; press the button four times to enter the random play mode; press
the button five times to exit.
ALBUM SELECTING
1. During MP3/USB playback, Press and hold the +10/ALBUM button till an album number
“F…” flashes on the screen.
2. Rotate the TUN+/-&NEXT/PREV CONTROL repeatedly until the number of your desired
album flashes on the screen, release the TUN+/-&NEXT/PREV CONTROL.
3. Press the +10/ALBUM button again to start the playback from the first track of the
selected album.
PROGRAMMED PLAY (CD/MP3 DISC/USB)
1. At stop mode, press the MODE/PROG/MEM button once, the program’s icon shows with
a program sequence indication "P01" first, then a track number flickers on the LCD with
the program’s icon;
2. Select the first track to be programmed using the TUN+/-&NEXT/PREV CONTROL or
+10/ALBUM button, and then press the MODE/PROG/MEM button again to store and
advance to the next programming step (If there are several folders on the MP3 disc or
USB, it is necessary to program folders first and then the tracks. The method of the
folders programming is the same as the tracks programming.).
3. Repeat the above steps to program more tracks. A maximum of 20 tracks for CD and 99
tracks for MP3/USB can be programmed in memory in a preferred order. If the memory is
full, the screen will show “FUL” for indicating.
4. Press the PLAY/PAUSE/CH+ button to begin programmed play in the preferred order
after you are done with programming. The player stops automatically after all
programmed tracks are played.
5. You may press the STOP/CH- button to terminate programmed playback. In program stop
mode, press the PLAY/PAUSE/CH+ button to begin the programmed playback with the
programming order identical with the previous one done; press the STOP/CH- button
again to clear the programming.
AUX IN
1. Connect the AUX IN jack on the unit to an audio source, for example, MP3 player with an
audio cable.
2. Power on the unit following the corresponding instructions.
3. Press the SOURCE button repeatedly to switch to AUX mode.
4. Use the native controls on the connected audio device to begin playing music through the
connected unit.
IMPORTANT SAFETY INSTRUCTIONS
The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
When the AC/DC adapter is used as the disconnect device, the disconnect device shall
remain readily operable. To be completely disconnected the power input, the AC/DC
adapter shall be disconnected from the mains completely.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Minimum distances 2.0cm around the apparatus for sufficient ventilation. The ventilation
should not be impeded by covering the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
The use of apparatus is in tropical and/or moderate climates.
Attention should be drawn to the environmental aspects of battery disposal.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
The marking plate is located at the bottom of the apparatus.
STATEMENT OF COMPLIANCE:
Flamagas SA hereby declares that the DBU-37 product complies with the requisites and
basic safety requirements of: Directive 2004/108/EC on Electromagnetic Compatibility.
For a full copy of the statement of compliance please see:
www.electronicaflamagas.com
