background image

GUARANTEE

WARRANTY DOES NOT COVER

Product model

Serial number 

Username

Date of sale

Company

Client's signature

The warranty period starts from the date of sale of the products and covers 6 months for all power products.

During the warranty period, free failures caused due to the use of poor-quality materials in the production and 
manufacturer workmanship admitted fault are removed. The guarantee comes into force only when warranty card 
and cutting coupons are properly filled. The product is accepted for repair in its pure form and full completeness.

 

• Mechanical damage (cracks, chips, etc.) and damage 
caused by exposure to aggressive media, foreign objects 
inside the unit and air vents, as well as for damage occurred 
as a result of improper storage (corrosion of metal parts);
• Failures caused by overloading or product misuse, use of 
the product for other purposes. A sure sign of overload 
products is melting or discoloration of parts due to the high 
temperature, simultaneous failure of two or more nodes, 
teaser on the surfaces of the cylinder and the piston or 
destruction of piston rings. Also, the warranty does not 
cover failure of the automatic voltage regulator due to 
incorrect operation;
• Failure caused by clogging of the fuel and cooling systems;
• Wearing parts (carbon brushes, belts, rubber seals, oil 
seals, shock absorbers, springs, clutches, spark plugs, 

mufflers, nozzles, pulleys, guide rollers, cables, recoil starter, 
chucks, collets, removable batteries, filters and safety 
elements, grease, removable devices, equipment, knives, 
drills, etc.);
• Electrical cables with mechanical and thermal damage;
• Product opened or repaired by a non-authorized service center.
• Prevention, care products (cleaning, washing, lubrication, 
etc.), installation and configuration of the product;
• Natural wear products (production share);
• Failures caused by using the product for the needs related 
to business activities;
• If the warranty card is empty or missing seal (stamp) of the Seller;
• The absence of the holder's signature on the warranty card.

WARRANTY CARD

The product is in good conditions and fully complete. Read and agree the terms of the warranty.

Product

Model

Company

Date 
of sale

Product

Model

Company

Date 
of sale

Product

Model

Company

Date 
of sale

Summary of Contents for DASP600L





















Reviews: