background image

 

6

 
 
 
 
 
 
 
 
 
 
 
 
The technical data and performance index listed above should be used for reference 
only. They are subject to change. 

*

The actual quantity of ice produced per day can vary with room and water 

conditions.

 

 

INTRODUCTION 

 

AZ series Ice Maker finds wide application in households, bars, restaurants, hotels, 
supermarkets, etc. It produces crystal-clear, gourmet cube ice, and offers 
convenience for homeowners and hotel guests. An insulated ice storage bin is built 
into the ice maker. 
This user's manual is intended as a resource for persons installing, using and 
servicing the AZ series. It contains valuable information on safety and maintenance. 
My company strongly recommends that this manual be kept in a place where

 

it can 

be accessed when needed. 
The ice maker is designed and manufactured according to the highest standards of 
safety and performance.   
My company assumes no liability or responsibility of any kind for products 
manufactured that have been altered in any way, including the use of any parts 
and/or other components not specifically approved by my company. My company 
reserves the right to make design changes and/or improvements at any time. 
Specifications and designs are subject to change without notice. 

 

 

 

 

 

E v a p o r a t o r   s e n s o r

C o n d e n s e r   s e n s o r

I c e   f u l l   s e n s o r

E

N

L

P o we r   s wi t c h

B

C

P

C i r c u i t   Di a g r a m

F a n   mo t o r

P u mp

C o mp r e s s o r

Ga s  V a l v e

Wa t e r  V a l v e

Summary of Contents for DIM-70






























Reviews: