9
CUTTING HEIGHT ADJUSTMENT
To obtain the desired cutting height, the front and rear axles are repositioned on the underside of
the mower housing.
Warning! Disconnect the mower from the power supply and ensure the blade has stopped coasting
before adjusting the height.
1. To adjust the front wheel cutting height position (fig. 2a)
1) Turn the mower upside down.
2) Pull the wheel axle towards the front of the mower.
3) Locate the wheel axle into the desired cutting height adjustment position.
Note: Make sure that both front right and left wheels are located in the same cutting height adjust-
ment position.
2. To adjust the rear wheel cutting height position (fig. 2b)
1) Turn the mower on its side.
2) Pull the rear wheel axle towards the mower’s catcher flap.
3) Locate the wheel axle into the desire cutting height adjustment position.
Note: Make sure that both rear right and left wheel are located in the same cutting height adjustment
position.
3. Cutting height positions (fig.2c)
1) 25mm (lowest cutting height position)
2) 40mm
3) 55mm(highest cutting height position)
3. OPERATING
Connect to power supply
Warning!
Before connecting to the mains supply, always check the switch is in off position. Connect
the plug into the RCD protected power supply.
Starting
On/Off switch fig.3)
Caution! Do not start the mower if it is standing in long grass. Press the safety button (A) of the
switch assembly and then pull the switch lever (B) against the bar. Keep the switch lever held whilst
releasing the safety button. To stop the mower release the switch lever and it automatically returns
to its off position.
Mowing (fig.4)
We recommend to use your mower as outlined in this section in order to achieve optimum results
and to reduce the risk of cutting the mains cable.
• Place the bulk of the mains cable on the close to the starting point.
• Switch the mower on as described above.
• Proceed as shown in fig.4
• Move from position 1 to position 2
• Turn right and proceed towards position 3
• Turn left and move towards position 4
• Repeat the above procedures as required.
Warning! Do not work towards the cable.
Blade maintenance(fig.5)
• Regularly remove grass and dirt from the blade.
• At the beginning of the gardening season, carefully examine the condition of the blade.
• If the blade is very blunt, sharpen or replace the blade.
• If the blade is damaged or worn, fit a new blade.
If the blade is slipping, put the screwdriver into the location hole, tighten the blade by wrench. see
fig.6 and fig.7
Warning! Observe the following precautions:
• Disconnect the mower from the mains and wait until the blade has stopped rotating before proce-
eding.
• Be careful not to cut yourself. Use heavy-duty gloves or a cloth to grip the blade.
• Only use the specified replacement blade.
• Do not remove the impeller (A)for any reason.
To replace the blade:
• Turn the mower onto its side.
• Place bushing into shaft of motor
• Place blade screw into the holes
• Tighten blade screw with sleeve.
4. MAINTENANCE
1. Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe working condition.
2. Check the catcher frequently for wear or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt and impeller specified for this product.
5. Be careful during adjustments of the lawn mower to prevent entrapment of the fingers between
moving blade and fixed parts of the machine.
6. Oil the wheel pins.
7. Store the lawn mower in a dry place.
5. TECHNICAL SPECIFICATIONS
DLMJ1500E
Voltage: 230 V~ 50Hz
Power rating: 1500 W
No load speed: 3500 rpm
Cutting height: 3 height positions 20/40/60 mm
Max cutting width: 360 mm
Grass collection bag: 50 L fabric
Motor type: Brush motor
Wheels: front 5" / rear 7"
Noise level: 96 dB
7
6
