Daewoo DWD-M8011 Service Manual Download

Page: 29 / 31

TROUBLESHOOTING GUIDE

CAUSE

The water is supplied continuously due to an
inferior valve inlet.

The valve inlet is normal, but the water level
sensor (sensor pressure) is inferior.

The drain motor dose not work. (The drain
motor is an inferior product or broke down.)

Water leaks from the tub or the hose drain.

The motor spins into an opposite direction.

The motor hall IC is an inferior product or broke
down.

The motor is not normally connected.

The motor does not work. (The motor is an
inferior product or broke down.)

The water level sensor is an inferior product.

The thermistor wash is an inferior product or
broke down.

The thermistor wash is not connected normally.

The heater worked without the water in the tub.

The thermistor wash is an inferior product or
broke down.

The water temp. is over 45°C in delicate & wool
course. (The thermistor wash is an inferior
product or broke down.)

The heater wash dose not work. (The water
temp. doesn't rise over 2°C during 15min.)

The heater worked without the water in the tub.

The drain pump filter is clogged.

The drain pump does not work during spin.

The large amount of detergent was used.

The drain hose is placed higher than 1m above
the floor.

MESSAGE

PFE

ERROR

OVERFLOW

ERROR

LEAKAGE

ERROR

DIRECTION

ERROR

MOTOR

ERROR

SENSOR

PRESSURE

ERROR

THERMISTOR

WASH ERROR

THERMISTOR

WASH

OVERHEATING

ERROR

WATER TEMP.

ERROR

HEATER WASH

ERROR

HEATER

WASH

OVERHEATING

ERROR

PUMP FILTER

ERROR

SOLUTION

Change the valve inlet.

Change the water level sensor (sensor
pressure).

Change the drain motor.

Check the leak of the tub or the hose drain.
Then change the tub or the hose drain.

Change the PCB ASS’Y or the motor.

Change the motor hall IC or the motor.

Check the connector of the motor.

Change the motor.

Change the water level sensor.

Change the thermistor wash.

Check the connector of the thermistor
wash.

Check the water level.

Change the thermistor wash.

Change the heater wash.

Check the water level and the heater
wash.

Clean the drain pump filter.

Change the drain pump.

Use the proper amount of detergent.

Place the drain hose 1m below the floor

Summary of Contents for DWD-M8011
































Search results

Summary of Contents for DWD-M8011

Reviews:

Related manuals for DWD-M8011

Brands by name

Popular brands

Daewoo DWD-M8011, Service Manual

Search results

Summary of Contents for DWD-M8011

Reviews:

Related manuals for DWD-M8011

Brands by name

Popular brands