Dahua Technology DH-XVR42 AN-I Series, User Manual

Share

Page: 49 / 392

background image

User’s Manual

39

Icon

Description

NO1 C1, NO2 C2,
NO3 C3

There are four groups of normally open activation output (on/off button).

Ground cable.

485 A/B

485 communication port. They are used to control devices such as decoder.
120 Ω should be parallel connected between A, B lines if there are too many
PTZ decoders.

4.3.2

Alarm Input

Refer to the following figure for more information.



Grounding alarm inputs which includes NO (Normally Open) and NC (Normally Closed) type.



Parallel connect COM end and GND end of the alarm detector (Provide external power to the
alarm detector).



Parallel connect the Ground of the DVR and the ground of the alarm detector.



Connect the NC port of the alarm sensor to the DVR alarm input (ALARM).



Use the same ground with that of DVR if you use external power to the alarm device.

Alarm input

4.3.3

Alarm Output



Provide external power to external alarm device.



To avoid overloading, read the following relay parameters table carefully.



RS-485 A/B cable is for the A/B cable of the PTZ decoder.

4.3.4

Alarm Output Relay Parameters

Refer to the actual product for relay model information.

«
...
47
48
49
50
51
...
»

Summary of Contents for DH-XVR42 AN-I Series









































































































































































































































































































































































































Reviews:

No comments

Related manuals for DH-XVR42 AN-I Series

Brand: Speco Pages: 12

Brand: Dedicated Micros Pages: 2

Brand: e-Line Technology Pages: 147

Brand: Avtech Pages: 17

STANDALONE DVR HSDVR-3308A

Brand: HEXA Pages: 64

Brand: Genie Pages: 16

Brand: SKYTRONIC Pages: 36

Brand: Samsung Pages: 51

Brand: Samsung Pages: 89

Brand: Samsung Pages: 88

Brand: Samsung Pages: 101

Brand: Samsung Pages: 116

Brand: Samsung Pages: 127

Brand: Samsung Pages: 129

Brand: Samsung Pages: 175

Brand: Sanyo Pages: 4

Brand: Sanyo Pages: 16

Brand: Sanyo Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands