Dahua 1206761 Installation Manual Download

Page: 2 / 25

Table of Contents

SPEED DOME INSTALLATION

.......................................................................... 1

1.1

Installation Environments

..................................................................................................................... 1

1.2

Check installation space and installation location intension

........................................................... 1

1.3

About cable

............................................................................................................................................. 1

1.4

Select required power supply cable according to transmission distance

...................................... 2

1.5

Please keep all package material well for future use

....................................................................... 2

SETUP BEFORE INSTALLATION

...................................................................... 3

2.1

Check Accessories

................................................................................................................................ 3

2.2

Open Device

........................................................................................................................................... 3

2.3

Dial Switch Setup

................................................................................................................................... 3

2.3.1

Dial Location and Function

.............................................................................................................. 3

2.3.2

Dial Setting

......................................................................................................................................... 5

2.3.3

Address Setting

................................................................................................................................. 5

2.3.4

Baud Rate, Parity and HD/SD Video Mode Setting

..................................................................... 5

2.3.5

Terminal Matching Resistance Setup

............................................................................................ 6

2.4

RESET and SD Card Installation (Network Speed Dome)

.............................................................. 7

2.5

Cable Connection

.................................................................................................................................. 7

INSTALLATION

................................................................................................... 9

Summary of Contents for 1206761


























Search results

Summary of Contents for 1206761

Reviews:

Related manuals for 1206761

Brands by name

Popular brands

Dahua 1206761, Installation Manual

Search results

Summary of Contents for 1206761

Reviews:

Related manuals for 1206761

Brands by name

Popular brands