background image

 

 

11 

4.1  Cable Requirements 

The HDCVI PTZ requires the following minimum specifications for the coaxial cable used to transmit 

video: 

 

75 Ohm Resistance 

 

Full-cable with copper conductor 

 

95% knitted copper shield 

Transmission distances

1

 depend on the type of coaxial cable used and the maximum video resolution: 

RG-59/U Coax 

720p: 

500 m   (1640.42 ft) 

1080p:  400 m   (1312.34 ft) 
4 MP: 

300 m 

(984.25 ft) 

RG-6/U Coax 

720p: 

800 m   (2624.67 ft) 

1080p:  600 m   (1968.50 ft) 
4 MP: 

600 m   (1968.50 ft) 

CAT 6 UTP 
(balun required) 

720p: 

380 m   (1246.72 ft) 

1080p:  380 m   (1246.72 ft) 
4 MP: 

200 m 

(656.17 ft) 

4.2  Preparing for Installation 

The HDCVI PTZ camera comes with the 64FB Wall Mount, the installer must supply the following 

hardware: 

 

Four (4) bolts, washers or other fastening hardware to secure the wall mount to the installation 

medium. The hardware must be capable of supporting eight (8) times the weight of the camera 

and mount. 

 

Appropriate tools to mount the camera to the wall. 

4.3  Mounting the Camera to a Wall 

1.  Remove the camera, the mount accessories, and any hardware packages from the boxes. 

2.  Place the 64FB Wall Mount against the wall and mark the location of the center hole and the four 

perimeter mounting holes. 

 

3.  Pre-drill the four perimeter holes as marked on the wall for the fasteners, using a drill bit that is no 

wider than the fastener.  

4.  Drill a 50-mm (approximately 2 in.) center hole to route the cables, if necessary.  

                                                 

1

 Transmission distance results verified by real-scene testing in Dahua's test laboratory. Actual transmission distances may 

vary due to external influences, cable quality, and wiring structures. 

Summary of Contents for 6C430IC

















Reviews: