background image

                                                               

 

 

iii 

Important Safeguards and Warnings  

1

Electrical safety 

 

All installation and operation here should conform to your local electrical safety codes.  

 

An apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a 

protective earthing connection.  

 

Use a power supply which meets the requirements for SELV (Safety Extra Low Voltage) and 

complies with Limited Power Source according to IEC 60950-1. Refer to the device label for 

detailed information.  

 

The product must be grounded to reduce the risk of electric shock. 

 

We assume no liability or responsibility for all the fires or electric shock caused by improper 

handling or installation.  

2

Transportation security 

 

Heavy stress, violent vibration or water splash are not allowed during transportation, storage 

and installation. 

3

Installation 

 

Keep upwards. Handle with care.  

 

Do not apply power to the NVR before completing installation.  

 

Do not place objects on the NVR. 

4

Qualified engineers needed 

 

 

All the examination and repair work should be done by the qualified service engineers.   

 

We are not liable for any problems caused by unauthorized modifications or attempted repair. 

5

Environment 

 

The NVR should be installed in a cool, dry place away from direct sunlight, inflammable, 

explosive substances and etc. 

 

This series product shall be transported, storage and used in the specified environments. 

 

Environment which needs to comply with the following conditions: 

  The function of the ITE being investigated to IEC 60950-1 is considered not likely to require 

connection to an Ethernet network with outside plant routing, including campus environment.  

  The  installation  instructions  clearly  state  that  the  ITE  is  to  be  connected  only  to  PoE 

networks without routing to the outside plant.  

 

6.  Accessories 

 

Be sure to use all the accessories recommended by manufacturer. 

 

Before installation, please open the package and check all the components are included. 

 

Contact your local retailer ASAP if something is broken in your package. 

 

7. Lithium battery 

 

 

Improper battery use may result in fire, explosion, or personal injury!  

 

When replace the battery, please make sure you are using the same model! 

CAUTION 

Summary of Contents for DHI-NVR5224-24P-4KS2

























Reviews: