Dahua iDVR&iHCVR User Manual Download

Page: 186 / 262

Dahua iDVR&iHCVR

User’s Manual

177

5.9.2 Network

5.9.2.1 TCP/IP

The TCP/IP interface is shown as in Figure 5-27.

Figure 5-27

Please refer to the following sheet for detailed information.

Parameter

Function

Mode

There are two modes: static mode and the DHCP mode.



The IP/submask/gateway are null when you select the
DHCP mode to auto search the IP.



If you select the static mode, you need to set the
IP/submask/gateway manually.



If you select the DHCP mode, you can view the
IP/submask/gateway from the DHCP.



If you switch from the DHCP mode to the static mode, you
need to reset the IP parameters.



Besides, IP/submask/gateway and DHCP are read-only
when the PPPoE dial is OK.

Mac Address

It is to display host Mac address.

IP Version

It is to select IP version. IPV4 or IPV6.

You can access the IP address of these two versions.

IP Address

Please use the keyboard to input the corresponding number to
modify the IP address and then set the corresponding subnet
mask and the default gateway.

Preferred DNS

DNS IP address.

Summary of Contents for iDVR&iHCVR







































































































































































































































































Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands

Dahua iDVR&iHCVR, User Manual

Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands