Dahua iDVR&iHCVR User Manual Download | Manualshive

Page: 208 / 262

background image

Dahua iDVR&iHCVR

User’s Manual

199

Parameter

Function

whole week.

Click OK button, system goes back to local alarm
interface, please click save button to exit.

Anti-dither

System only memorizes one event during the anti-dither
period. The value ranges from 5s to 600s.

Sensor type

There are two options: NO/NC.

Record channel

System auto activates motion detection channel(s) to
record once an alarm occurs. Please note you need to set
alarm record period and go to Storage-> Schedule to set
current channel as schedule record.

Record Delay

System can delay the record for specified time after alarm
ended. The value ranges from 10s to 300s.

Alarm out

Enable alarm activation function. You need to select alarm
output port so that system can activate corresponding
alarm device when an alarm occurs.

Latch

System can delay the alarm output for specified time after
an alarm ended. The value ranges from 1s to 300s.

Show message

System can pop up a message to alarm you in the local
host screen if you enabled this function.

Buzzer

Check the box here to enable this function. The buzzer
beeps when an alarm occurs.

Alarm upload

System can upload the alarm signal to the centre
(Including alarm centre).

Send Email

If you enabled this function, System can send out an email
to alert you when an alarm occurs.

Tour

You need to check the box here to enable this function.
System begins 1-wiindow or multiple-window tour display
among the channel(s) you set to record when an alarm
occurs.

PTZ Activation

Here you can set PTZ movement when alarm occurs.
Such as go to preset X.

5.9.3.3.2 Net Alarm

The network alarm interface is shown as in Figure 5-65.

Network alarm refers to the alarm signal from the network. System does not anti-dither

and sensor type setup. For setup information, please refer to chapter 5.9.3.3.1.

«
...
206
207
208
209
210
...
»

Summary of Contents for iDVR&iHCVR







































































































































































































































































Reviews:

No comments

Related manuals for iDVR&iHCVR

Brand: ESP Pages: 21

Brand: EverFocus Pages: 152

Brand: Eneo Pages: 88

MultiView MV-DR4000

Brand: AVE Pages: 87

Brand: Swann Pages: 2

Brand: Watchguard Pages: 19

NHDR 4000 Series

Brand: Novus Pages: 24

Brand: Bosch Pages: 12

Brand: Samsung Pages: 1

Brand: Samsung Pages: 1

Brand: Samsung Pages: 2

Brand: Samsung Pages: 1

Brand: Samsung Pages: 23

Brand: Samsung Pages: 45

Brand: Samsung Pages: 68

Brand: Samsung Pages: 93

Brand: Samsung Pages: 92

Brand: Samsung Pages: 109

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands