Dahua iDVR&iHCVR User Manual Download

Page: 210 / 262

Dahua iDVR&iHCVR

User’s Manual

201

Figure 5-68

Please refer to the following sheet for detailed information.

Parameter Function

Event
Type

The abnormal events include: No disk, disk error, disk no space, net
disconnection, IP conflict and MAC conflict.

You can set one or more items here.

Less than: You can set the minimum percentage value here (For disk
not space only). The device can alarm when capacity is not sufficient.

You need to draw a circle to enable this function.

Enable

Check the box here to enable selected function.

Alarm Out

Please select corresponding alarm output channel when an alarm
occurs. You need to check the box to enable this function.

Latch

The alarm output can delay for the specified time after an alarm stops.
The value ranges from 1s to 300s.

Show
message

System can pop up a message to alarm you in the local host screen if
you enabled this function.

Alarm
upload

System can upload the alarm signal to the centre (Including alarm
centre.

Send
Email

If you enabled this function, System can send out an email to alert you
when an alarm occurs.

Buzzer

Check the box here to enable this function. The buzzer beeps when an
alarm occurs.

5.9.4 Storage

5.9.4.1 Schedule

In this interfaces, you can add or remove the schedule record setup. See Figure 5-69.

There are three record modes: general (auto), motion detect and alarm. There are six

periods in one day.

You can view the current time period setup from the color bar.



Green color stands for the general record/snapshot.



Yellow color stands for the motion detect record/snapshot..



Red color stands for the alarm record/snapshot.



Blue color stands for MD&alarm record/snapshot.

Summary of Contents for iDVR&iHCVR







































































































































































































































































Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands

Dahua iDVR&iHCVR, User Manual

Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands