Dahua iDVR&iHCVR User Manual Download

Page: 238 / 262

Dahua iDVR&iHCVR

User’s Manual

229



PTZ decoder setup, connection or installation is not correct.



Cable connection is not correct.



PTZ setup is not correct.



PTZ decoder and DVR protocol is not compatible.



PTZ decoder and DVR address is not compatible.



When there are several decoders, please add 120 Ohm between the PTZ

decoder A/B cables furthest end to delete the reverberation or impedance

matching. Otherwise the PTZ control is not stable.



The distance is too far.

12. Motion detection function does not work.

There are following possibilities:



Period setup is not correct.



Motion detection zone setup is not correct.



Sensitivity is too low.



For some versions, there is hardware limit.

13. I can not log in client-end or web.

There are following possibilities:



For Windows 98 or Windows ME user, please update your system to Windows

2000 sp4. Or you can install client-end software of lower version. Please note

right now, our DVR is not compatible with Windows VISTA control.



ActiveX control has been disabled.



No dx8.1 or higher. Please upgrade display card driver.



Network connection error.



Network setup error.



Password or user name is invalid.



Client-end is not compatible with DVR program.

14. There is only mosaic no video when preview or playback video file remotely.

There are following possibilities:



Network fluency is not good.



Client-end resources are limit.



There is multiple-cast group setup in DVR. This mode can result in mosaic.

Usually we do not recommend this mode.



There is privacy mask or channel protection setup.



Current user has no right to monitor.



DVR local video output quality is not good.

15. Network connection is not stable.

There are following possibilities:



Network is not stable.



IP address conflict.

Summary of Contents for iDVR&iHCVR







































































































































































































































































Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands

Dahua iDVR&iHCVR, User Manual

Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands