Dahua iDVR&iHCVR User Manual Download

Page: 9 / 262

Dahua iDVR&iHCVR

User’s Manual

viii

Important Safeguards and Warnings

．

Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The product must be grounded to reduce the risk of electric shock.

We assume no liability or responsibility for all the fires or electric shock caused by

improper handling or installation.

．

Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation,

storage and installation.

．

Installation

Keep upwards. Handle with care.

Do not apply power to the DVR before completing installation.

Do not place objects on the DVR.

．

Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted

repair.

．

Environment

The DVR should be installed in a cool, dry place away from direct sunlight, inflammable,

explosive substances and etc.

6. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

7. Lithium battery

Improper battery use may result in fire, explosion, or personal injury!

When replace the battery, please make sure you are using the same model!

Summary of Contents for iDVR&iHCVR







































































































































































































































































Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands

Dahua iDVR&iHCVR, User Manual

Search results

Summary of Contents for iDVR&iHCVR

Reviews:

Related manuals for iDVR&iHCVR

Brands by name

Popular brands