background image

 

 

iii 

 

 

Important Safeguards and Warnings  

1

Electrical safety 

All installation and operation here should conform to your local electrical safety codes.  

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited 

power source is rated 12V DC (24V AC) in the IEC60950-1. 

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling 

or installation.  

 

2

Transportation security 

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and 

installation. 

 

3

Installation 

Do not apply power to the radar before completing installation.  

Always follow the instruction guide the manufacturer recommended. 

 

4

Qualified engineers needed 

 

All the examination and repair work should be done by the qualified service engineers.   

We are not liable for any problems caused by unauthorized modifications or attempted repair. 

 

5

Environment 

The working temperature ranges from -30

 to +70

. Please keep it away from the electromagnetic 

radiation object and environment. 

Please keep the sound ventilation.  

Do not allow the water and other liquid falling into the radar. 

 

6.  Accessories 

Be sure to use all the accessories recommended by manufacturer. 

Before installation, please open the package and check all the components are included. 

Contact your local retailer ASAP if something is broken in your package. 

 
 

Summary of Contents for ITARD-024SA















Reviews: