Daikin altherma ERHQ014BAV3, Installation Manual

ERHQ011~W1 + ERLQ011~W1

Outdoor unit for air to water heat pump

4PW57794-1 – 08.2010

Installation manual

24

19. W

IRING

DIAGRAM

A1P~A4P ......................Printed circuit board

BS1~BS4 ......................Push button switch

C1~C4 ..........................Capacitor

DS1...............................DIP switch

E1H...............................Bottom plate heater

E1HC ............................Crankcase heater

F1U~F9U ......................Fuse

HAP (A1P) ....................Service monitor (green)

HAP (A2P) ....................Service monitor (green) (for W1 models only)

H1P~H7P (A1P) ...........Service monitor (orange) (for W1 models

only)

H1P~H7P (A2P) ...........Service monitor (orange)

K1M, K2M.....................Magnetic contactor (for W1 models only)

K1R~K4R .....................Magnetic relay

K10R, K11R..................Magnetic relay (for V3 models only)

L1R~L4R ......................Reactor

M1C ..............................Motor (compressor)

M1F ..............................Motor (fan) (upper)

M2F ..............................Motor (fan) (lower)

PS.................................Switching power supply

Q1DI .............................Earth leakage circuit breaker (field supply)

R1~R4 ..........................Resistor

R1T...............................Thermistor (air)

R2T...............................Thermistor (discharge)

R3T...............................Thermistor (suction pipe)

R4T...............................Thermistor (heat exchanger)

R5T .............................. Thermistor (heat exchanger middle)

R6T .............................. Thermistor (liquid)

R7T .............................. Thermistor (fin) (for W1 models only)

R10T ............................ Thermistor (fin) (for V3 models only)

RC................................ Signal receiver circuit (for V3 models only)

S1NPH ......................... Pressure sensor

S1PH............................ Pressure switch (high)

TC ................................ Signal transmission circuit (for V3 models

only)

V1R .............................. Power module (for V3 models only)

V1R, V2R ..................... Power module (for W1 models only)

V2R, V3R ..................... Diode module (for V3 models only)

V3R .............................. Diode module (for W1 models only)

V1T .............................. Insulated gate bipolar transistor (for V3

models only)

X1M.............................. Terminal strip

X1Y ................................Connector (option, bottom plate heater ERHQ)

X6A .............................. Connector (option)

X77A ............................ Connector

Y1E .............................. Expansion valve (main)

Y3E .............................. Expansion valve (injection)(for ERLQ only)

Y1S .............................. Solenoid valve (4-way valve)

Y3S .............................. Solenoid valve (for W1 models only, ERHQ)

Y3S ................................Solenoid valve (hot gas pass)(for ERLQ only)

Z1C~Z9C ..................... Noise filter

Z1F~Z4F ...................... Noise filter

: Wire clamp

L

: Live

: Terminal strip

N

: Neutral

: Connector

: Relay connector

BLK

: Black

ORG

: Orange

: Field wiring

BLU

: Blue

RED

: Red

: Protective earth screw

BRN

: Brown

WHT

: White

: Noiseless earth

GRN

: Green

YLW

: Yellow

NOTE 1

This wiring diagram only applies to the outdoor unit

NOTE 4

Refer to the option manual for connecting wiring to X6A/X77A

NOTE 5

Refer to the wiring diagram sticker (on back of front panel) on how to use BS1~BS4 and DS1 switch

NOTE 6

Do not operate the unit by short-circuiting protection device S1PH

NOTE 8

Confirm the method of setting the selector switches (DS1) by service manual. Factory setting of all switches: 'OFF'

NOTE 9

Option: Option
Wiring depending on model: Wiring depending on model