background image

2

1 IM-5WMYJ-0113(2)DAIKIN_EN.indd4   4

1 IM-5WMYJ-0113(2)DAIKIN_EN.indd4   4

6/10/14   10:07:24 AM

6/10/14   10:07:24 AM

English

!

WARNING

!

CAUTION

Installation and maintenance should be performed by quali

fi

 ed 

persons who are familiar with local code and regulation, and 
experienced with this type of appliance.
Con

fi

 rm

 

that the unit has been switched OFF before 

installing or servicing the unit.
Risk of electric shock, can cause injury or death. Disconnect all 
remain electric power supplies before servicing.
DO NOT pull out the power cord when the power is ON. 
This may cause serious electrical shocks which may result 
in 

fire

 hazards.

Please take note of the following important points when 
installing.
• Do not install the unit where leakage of flammable gas may 

 

Improper connection or fastening can 

 cause fire or electrical shock.

Do not handle with wet hands/ wash the unit with water.

  Electrical shock may occur.

Do not operate any heating apparatus too close to the 

gateway

 or use in room where mineral oil, oil 

vapor

 or oil 

steam exist, this may cause plastic part to melt or 
deform as a result of excessive heat or chemical reaction.

 

Don’t use joined and twisted wires for incoming power 
supply.
The equipment is not intended for use in a potentially 
explosive atmosphere.

SAFETY PRECAUTIONS

INSTALLATION MANUAL

This manual provides the procedures of installation to ensure a safe and good standard of 
operation for the 

BMS Access Gateway

.

 

Special adjustment may be necessary to suit local 

requirement.
Before using your 

gateway

, please read this instruction manual carefully and keep it for future 

reference.

 

This appliance is intended to be used by expert or trained users in shops, in light industry and 
on farms, or for commercial use by lay persons.
This appliance is not intended for use by persons, including children, with reduced physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been 
given supervision or instruction concerning use of the appliance by a person responsible for their 
safety.
Children should be supervised to ensure that they do not play with the appliance.

Use  only  the  recommended  cables  for  wiring.  The

co

n

nections  must  be  firm  but  without  tensioning

the terminals.

Summary of Contents for BAG
















Reviews: