Instruction
SiEN18-621
244
System Configuration
A. UP AND DOWN DIRECTION
•
The movable limit of the flap is changeable. Con-tact your
Daikin dealer for details.
Press the AIR FLOW DIRECTION ADJUST button
to select the air direction as following.
The AIR FLOW FLAP display swings as
shown left and the air flow direction
continuously varies. (Automatic swing
setting)
Press AIR FLOW DIRECTION ADJUST
button to select the air direction of your
choice.
The AIR FLOW FLAP display stops
swinging and the air flow direction is fixed
(Fixed air flow direction setting).
Movement of the air flow flap
For the following conditions, micro computer controls the air
flow direction so it may be different from the display.
Operation mode includes automatic operation.
A. LEFT AND RIGHT DIRECTION
•
Adjusting air flow direction in the left and right direction.
(Refer to Fig. 1)
NOTE
•
The movable limit of the flap is changeable. Contact your
Daikin dealer for details
Operate in the following order.
•
The timer is operated in the following two ways.
•
Programming the stop time (
) ... The system stops
operating after the set time has elapsed.
•
Programming the start time (
) ... The system starts
operating after the set time has elapsed.
•
The timer can be programmed a maximum of 72 hours.
•
The start and the stop time can be simultaneously
programmed.
Timer mode START/STOP
Press the TIMER MODE START/STOP button several
times and select the mode on the display.
The display flashes.
For setting the timer stop .... “
”
For setting the timer start ... “
”
Programming time
Press the PROGRAMMING TIME button and set the time
for stopping or starting the system.
When this button is pressed, the time advances by
1 hour.
When this button is pressed, the time goes
backward by 1 hour.
Timer ON/OFF
Press the TIMER ON/OFF button.
The timer setting procedure ends.
The display “
or
” changes from flashing light to
a constant light.
Refer to figure 4 on page [1]
NOTE
•
When setting the timer OFF and On at the same time,
repeat the above procedure from 1 to 3 once again.
When the timer is programmed to stop the system after 3
hours and start the system after 4 hours, the system will stop
after 3 hours and then 1 hour later the system will start.
•
After the timer is programmed, the display shows the
remaining time.
•
Press the TIMER ON/OFF button once again to cancel
programming. the display vanishes.
Operation
mode
Cooling
Heating
Operation
condition
•
When room
temperature is
lower than the set
temperature
•
When room
temperature is
higher than the set
temperature
•
At defrost
operation
•
When operating continuously at downward
air flow direction
A. Up
a
nd down
direction
B. Left
a
nd right direction
Fi
g
. 1
Program timer operation
1
2
3
Summary of Contents for BPMKS967B2B
